參數資料
型號: AD7711ARZ-REEL7
廠商: Analog Devices Inc
文件頁數: 15/28頁
文件大?。?/td> 0K
描述: IC ADC 24BIT RTD I SOURCE 24SOIC
標準包裝: 400
位數: 24
采樣率(每秒): 1.03k
數據接口: 串行
轉換器數目: 1
功率耗散(最大): 52.5mW
電壓電源: 模擬和數字,雙 ±
工作溫度: -40°C ~ 80°C
安裝類型: 表面貼裝
封裝/外殼: 24-SOIC(0.295",7.50mm 寬)
供應商設備封裝: 24-SOIC W
包裝: 帶卷 (TR)
輸入數目和類型: 1 個單端,單極;1 個單端,雙極;1 個差分,單極;1 個差分,雙極
REV. G
–22–
AD7711
Figures 12a and 12b show timing diagrams for reading from the
AD7711 in external clocking mode. In Figure 12a, all the data is
read from the AD7711 in one operation. In Figure 12b, the data
is read from the AD7711 over a number of read operations. Both
read operations show a read from the AD7711’s output data
register. A read from the control register or calibration registers is
similar, but, in these cases, the
DRDY line is not related to the
read function. Depending on the output update rate, it can go
low at any stage in the control/calibration register read cycle
without affecting the read, and its status should be ignored. A
read operation from either the control or calibration registers
must always read 24 bits of data.
Figure 12a shows a read operation from the AD7711 where
RFS remains low for the duration of the data-word transmission.
With
DRDY low, the RFS input is brought low. The input
SCLK signal should be low between read and write operations.
RFS going low places the MSB of the word to be read on the
serial data line. All subsequent data bits are clocked out on a
high to low transition of the serial clock and are valid prior to
the following rising edge of this clock. The penultimate falling
edge of SCLK clocks out the LSB and the final falling edge
resets the
DRDY line high. This rising edge of DRDY turns off
the serial data output.
Figure 12b shows a timing diagram for a read operation where
RFS returns high during the transmission of the word and
returns low again to access the rest of the data-word. Timing
parameters and functions are very similar to that outlined for
Figure 12a, but Figure 12b has a number of additional times to
show timing relationships when
RFS returns high in the middle
of transferring a word.
RFS should return high during a low time of SCLK. On the
rising edge of
RFS, the SDATA output is turned off. DRDY
remains low and will remain low until all bits of the data-word
are read from the AD7711, regardless of the number of times
RFS changes state during the read operation. Depending on the
time between the falling edge of SCLK and the rising edge of
RFS, the next bit (BIT N+1) may appear on the data bus before
RFS goes high. When RFS returns low again, it activates the
SDATA output. When the entire word is transmitted, the
DRDY line will go high, turning off the SDATA output as shown
in Figure 12a.
t20
SDATA (O)
SCLK (I)
RFS (I)
A0 (I)
DRDY (O)
t22
t24
t25
t26
t27
t29
t28
t23
t21
THREE-STATE
MSB
LSB
Figure 12a. External Clocking Mode, Output Data Read Operation
t20
SDATA (O)
SCLK (I)
RFS (I)
A0 (I)
DRDY (O)
t22
t24
t25
t26
t27
t24
t25
THREE-STATE
MSB
t30
t31
BIT N
BIT N+1
Figure 12b. External Clocking Mode, Output Data Read Operation (
RFS Returns High during Read Operation)
相關PDF資料
PDF描述
MS27468P13F35P CONN RCPT 22POS JAM NUT W/PINS
IDT7203L25P IC MEM FIFO 2048X9 25NS 28-DIP
LTC1609ACSW#TR IC ADC SRL 16BIT 200KSPS 20-SOIC
VI-2NK-MX-F1 CONVERTER MOD DC/DC 40V 75W
PT06W-12-3S CONN PLUG 3 POS STRAIGHT W/SCKT
相關代理商/技術參數
參數描述
AD7711ASQ 功能描述:模數轉換器 - ADC CMOS 24B w/ Matched RTD Excitation Crnt RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體:
AD7711SQ 制造商:Analog Devices 功能描述:- Rail/Tube
AD7712 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS Signal Conditioning ADC
AD7712_04 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS Signal Conditioning ADC