- 您現在的位置：買賣IC網 > PDF目錄373878 > AD5381BST-5 (ANALOG DEVICES INC) 32-Channel, 3 V/5 V, Single-Supply, 14-Bit, Voltage Output DAC PDF資料下載
參數資料
| 型號： | AD5381BST-5 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | DAC |
| 英文描述： | 32-Channel, 3 V/5 V, Single-Supply, 14-Bit, Voltage Output DAC |
| 中文描述： | PARALLEL, WORD INPUT LOADING, 6 us SETTLING TIME, 12-BIT DAC, PQFP100 |
| 封裝： | 14 X 14 MM, MS-026-BED, LQFP-100 |
| 文件頁數： | 28/36頁 |
| 文件大?。?/td> | 1200K |
| 代理商： | AD5381BST-5 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
AD5381
I
2
C SERIAL INTERFACE
The AD5381 features an I
2
C compatible 2-wire interface
consisting of a serial data line (SDA) and a serial clock line
(SCL). SDA and SCL facilitate communication between the
AD5381 and the master at rates up to 400 kHz. Figure 6 shows
the 2-wire interface timing diagrams that incorporate three
different modes of operation. In selecting the I
2
C operating
mode, first configure serial operating mode (SER/PAR = 1) and
then select I
2
C mode by configuring the SPI/I2C pin to a Logic
1. The device is connected to the I
2
C bus as a slave device (i.e.,
no clock is generated by the AD5381). The AD5381 has a 7-bit
slave address 1010 1(AD1)(AD0). The 5 MSB are hard-coded
and the 2 LSB are determined by the state of the AD1 and AD0
pins. The facility to hardware configure AD1 and AD0 allows
four of these devices to be configured on the bus.
I
2
C Data Transfer
One data bit is transferred during each SCL clock cycle. The
data on SDA must remain stable during the high period of the
SCL clock pulse. Changes in SDA while SCL is high are control
signals that configure START and STOP conditions. Both SDA
and SCL are pulled high by the external pull-up resistors when
the I
2
C bus is not busy.
START and STOP Conditions
A master device initiates communication by issuing a START
condition. A START condition is a high-to-low transition on
SDA with SCL high. A STOP condition is a low-to-high
transition on SDA while SCL is high. A START condition from
the master signals the beginning of a transmission to the
AD5381. The STOP condition frees the bus. If a repeated
START condition (Sr) is generated instead of a STOP condition,
the bus remains active.
Repeated START Conditions
A repeated START (Sr) condition may indicate a change of data
direction on the bus. Sr may be used when the bus master is
writing to several I
2
C devices and wants to maintain control of
the bus.
Acknowledge Bit (ACK)
The acknowledge bit (ACK) is the ninth bit attached to any
8-bit data-word. ACK is always generated by the receiving
device. The AD5381 devices generate an ACK when receiving
an address or data by pulling SDA low during the ninth clock
period. Monitoring ACK allows for detection of unsuccessful
data transfers. An unsuccessful data transfer occurs if a
receiving device is busy or if a system fault has occurred. In the
event of an unsuccessful data transfer, the bus master should
reattempt communication.
Rev. A | Page 28 of 36
AD5381 Slave Addresses
A bus master initiates communication with a slave device by
issuing a START condition followed by the 7-bit slave address.
When idle, the AD5381 waits for a START condition followed
by its slave address. The LSB of the address word is the Read/
Write (R/W) bit. The AD5381 is a receive only device; when
communicating with the AD5381, R/W = 0. After receiving the
proper address 1010 1(AD1)(AD0), the AD5381 issues an ACK
by pulling SDA low for one clock cycle.
The AD5381 has four different user programmable addresses
determined by the AD1 and AD0 bits.
Write Operation
There are three specific modes in which data can be written to
the AD5381 DAC.
4-Byte Mode
When writing to the AD5381 DACs, the user must begin with
an address byte (R/W = 0) after which the DAC acknowledges
that it is prepared to receive data by pulling SDA low. The
address byte is followed by the pointer byte; this addresses the
specific channel in the DAC to be addressed and is also
acknowledged by the DAC. Two bytes of data are then written
to the DAC, as shown in Figure 31. A STOP condition follows.
This allows the user to update a single channel within the
AD5381 at any time and requires four bytes of data to be
transferred from the master.
3-Byte Mode
In 3-byte mode, the user can update more than one channel in a
write sequence without having to write the device address byte
each time. The device address byte is only required once; sub-
sequent channel updates require the pointer byte and the data
bytes. In 3-byte mode, the user begins with an address byte
(R/W = 0), after which the DAC will acknowledge that it is
prepared to receive data by pulling SDA low. The address byte is
followed by the pointer byte. This addresses the specific channel
in the DAC to be addressed and is also acknowledged by the
DAC. This is then followed by the two data bytes. REG1 and
REG0 determine the register to be updated.
If a STOP condition does not follow the data bytes, another
channel can be updated by sending a new pointer byte followed
by the data bytes. This mode only requires three bytes to be sent
to update any channel once the device has been initially
addressed, and reduces the software overhead in updating the
AD5381 channels. A STOP condition at any time exits this
mode. Figure 32 shows a typical configuration.
相關PDF資料 |
PDF描述 |
|---|---|
| AD5381BST-5-REEL | 40-Channel, 3 V/5 V, Single-Supply, 12-Bit, Voltage Output DAC |
| AD5382BST-3-REEL | CONNECTOR ACCESSORY |
| AD5382 | 32-Channel, 3 V/5 V, Single-Supply, 14-Bit, Voltage Output DAC |
| AD5382BST-3 | 32-Channel, 3 V/5 V, Single-Supply, 14-Bit, Voltage Output DAC |
| AD5382BST-5 | 32-Channel, 3 V/5 V, Single-Supply, 14-Bit, Voltage Output DAC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5381BST-5-REEL | 制造商:Analog Devices 功能描述:DAC 40-CH Resistor-String 12-bit 100-Pin LQFP T/R |
| AD5381BSTZ-3 | 功能描述:IC DAC 12BIT 40CHAN 3V 100LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:1 系列:- 設置時間:4.5µs 位數:12 數據接口:串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOICN 包裝:剪切帶 (CT) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:* 其它名稱:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
| AD5381BSTZ-3-REEL | 功能描述:IC DAC 12BIT 40CH 3V 100-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD5381BSTZ-5 | 功能描述:IC DAC 12BIT 40CH 5V 100-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD5381BSTZ-5-REEL | 功能描述:IC DAC 12BIT 40CH 5V 100-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
發布緊急采購，3分鐘左右您將得到回復。