- 您現在的位置：買賣IC網 > PDF目錄373869 > AD5165 (Analog Devices, Inc.) Circular Connector; No. of Contacts:4; Series:D38999; Body Material:Metal; Connecting Termination:Crimp; Connector Shell Size:13; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:13-4 PDF資料下載
參數資料
| 型號： | AD5165 |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | 圓形連接器 |
| 英文描述： | Circular Connector; No. of Contacts:4; Series:D38999; Body Material:Metal; Connecting Termination:Crimp; Connector Shell Size:13; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:13-4 |
| 中文描述： | 256位置，超低功耗1.8 V邏輯級數字電位器 |
| 文件頁數： | 13/16頁 |
| 文件大小： | 569K |
| 代理商： | AD5165 |
AD5165
THEORY OF OPERATION
The AD5165 is a 256-position digitally controlled variable
resistor (VR) device.
Rev. 0 | Page 13 of 16
PROGRAMMING THE VARIABLE RESISTOR
Rheostat Operation
The nominal resistance of the RDAC between terminals A and
B is available in 100 k. The nominal resistance (R
AB
) of the VR
has 256 contact points accessed by the wiper terminal, plus the
B terminal contact. The 8-bit data in the RDAC latch is decoded
to select one of the 256 possible settings.
A
W
B
A
W
B
A
W
B
0
Figure 36. Rheostat Mode Configuration
Assuming that a 100 k part is used, the wiper’s first connec-
tion starts at the B terminal for data 0x00. Because there is a
50 wiper contact resistance, such a connection yields a mini-
mum of 100 (2 × 50 ) resistance between terminals W and
B. The second connection is the first tap point, which corres-
ponds to 490 (
R
WB
=
R
AB
/256 + 2 ×
R
W
= 390 + 2 × 50 )
for data 0x01. The third connection is the next tap point,
representing 880 (2 × 390 + 2 × 50 ) for data 0x02, and
so on. Each LSB data value increase moves the wiper up the
resistor ladder until the last tap point is reached at 100,100
(
R
AB
+ 2 ×
R
W
).
D4
D3
D2
D1
D0
D7
D5
RDAC
LATCH
AND
DECODER
R
S
R
S
R
S
R
S
A
W
B
0
Figure 37. AD5165 Equivalent RDAC Circuit
The general equation determining the digitally programmed
output resistance between W and B is
W
AB
WB
R
R
D
D
R
×
+
×
=
2
256
)
(
(1)
where:
D
is the decimal equivalent of the binary code loaded in the
8-bit RDAC register.
R
AB
is the end-to-end resistance.
R
W
is the wiper resistance contributed by the on resistance of
the internal switch.
In summary, if
R
AB
= 100 k and the A terminal is open
circuited, the following output resistance
R
WB
is set for the
indicated RDAC latch codes.
Table 6. Codes and Corresponding R
WB
Resistance
D (Dec.)
R
WB
()
Output State
255
99,710
Full scale (
R
AB
– 1 LSB +
R
W
)
128
50,100
Midscale
1
490
1 LSB
0
100
Zero scale (wiper contact resistance)
Note that, in the zero-scale condition, a finite wiper resistance
of 100 is present. Care should be taken to limit the current
flow between W and B in this state to a maximum pulse current
of no more than 20 mA. Otherwise, degradation or possible
destruction of the internal switch contact can occur.
Similar to the mechanical potentiometer, the resistance of the
RDAC between the wiper W and terminal A also produces a
digitally controlled complementary resistance,
R
WA
. When these
terminals are used, the B terminal can be opened. Setting the
resistance value for R
WA
starts at a maximum value of resistance
and decreases as the data loaded in the latch increases in value.
The general equation for this operation is
W
AB
WA
R
R
D
D
R
×
+
×
=
2
256
256
)
(
(2)
For
R
AB
= 100 k with the B terminal open circuited, the
following output resistance R
WA
is set for the indicated RDAC
latch codes.
Table 7. Codes and Corresponding R
WA
Resistance
D (Dec.)
R
WA
()
255
490
128
50,100
1
99, 710
0
100,100
Output State
Full scale
Midscale
1 LSB
Zero scale
Typical device-to-device matching is process-lot dependent
and may vary by up to ±20%. Because the resistance element
is processed in thin film technology, the change in
R
AB
with
temperature has a very low 35 ppm/°C temperature coefficient.
相關PDF資料 |
PDF描述 |
|---|---|
| AD5170BRM10 | 256-Position Two-Time Programmable I2C Digital Potentiometer |
| AD5170BRM10-RL7 | 256-Position Two-Time Programmable I2C Digital Potentiometer |
| AD5170BRM100 | 256-Position Two-Time Programmable I2C Digital Potentiometer |
| AD5170BRM100-RL7 | 256-Position Two-Time Programmable I2C Digital Potentiometer |
| AD5170BRM2.5-RL7 | 256-Position Two-Time Programmable I2C Digital Potentiometer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5165BUJ100 | 制造商:Analog Devices 功能描述:DIG POT 256 5.5V 100KOHM 8 |
| AD5165BUJZ100 | 制造商:Analog Devices 功能描述:DIGIPOT 8BIT 3-WIRE 100K SMD 5165 制造商:Analog Devices 功能描述:DIGIPOT 8BIT 3-WIRE 100K, SMD, 5165 |
| AD5165BUJZ100-R2 | 功能描述:IC DGTL POT 100K LP TSOT23-8 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP（3x3） 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT |
| AD5165BUJZ100-R7 | 功能描述:IC DGTL POT 100K LP TSOT23-8 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| AD5165EVAL | 制造商:Analog Devices 功能描述:8-BIT 3-WIRE DIGIPOT1 - Bulk |
發布緊急采購，3分鐘左右您將得到回復。