- 您現在的位置：買賣IC網 > PDF目錄373867 > AD2S83 (Analog Devices, Inc.) Variable Resolution, Monolithic Resolver-to-Digital Converters(可變分辨率,單片解算-數字變換器) PDF資料下載
參數資料
| 型號： | AD2S83 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Variable Resolution, Monolithic Resolver-to-Digital Converters(可變分辨率,單片解算-數字變換器) |
| 中文描述： | 可變分辨率，單片分解到數字轉換器（可變分辨率，單片解算-數字變換器） |
| 文件頁數： | 9/19頁 |
| 文件大?。?/td> | 198K |
| 代理商： | AD2S83 |
AD2S83
–9–
REV. D
8. Offset Adjust
Offsets and bias currents at the integrator input can cause an
additional positional offset at the output of the converter of
1 arc minute typical, 5.3 arc minutes maximum. If this can be
tolerated, then R8 and R9 can be omitted from the circuit.
If fitted, the following values of R8 and R9 should be used:
R
8
=
4.7
M
,
R
9
=
1
M
potentiometer
To adjust the zero offset, ensure the resolver is disconnected
and all the external components are fitted. Connect the COS
pin to the REFERENCE INPUT and the SIN pin to the
SIGNAL GROUND and with the power and reference ap-
plied, adjust the potentiometer to give all “0s” on the digital
output bits.
The potentiometer may be replaced with select on test resistors
if preferred.
DATA TRANSFER
To transfer data the
INHIBIT
input should be used. The data
will be valid 490 ns after the application of a logic “LO” to the
INHIBIT
. This is regardless of the time when the
INHIBIT
is
applied and allows time for an active BUSY to clear. By using
the
ENABLE
input the two bytes of data can be transferred
after which the
INHIBIT
should be returned to a logic “HI”
state to enable the output latches to be updated.
BUSY Output
The validity of the output data is indicated by the state of the
BUSY output. When the input to the converter is changing, the
signal appearing on the BUSY output is a series of pulses at
TTL level. A BUSY pulse is initiated each time the input moves
by the analog equivalent of one LSB and the internal counter is
incremented or decremented.
INHIBIT
Input
The
INHIBIT
logic input only inhibits the data transfer from
the up-down counter to the output latches and, therefore, does
not interrupt the operation of the tracking loop. Releasing the
INHIBIT
automatically generates a BUSY pulse to refresh the
output data.
ENABLE
Input
The
ENABLE
input determines the state of the output data. A
logic “HI” maintains the output data pins in the high imped-
ance condition, and the application of a logic “LO” presents the
data in the latches to the output pins. The operation of the
ENABLE
has no effect on the conversion process.
BYTE SELECT Input
The BYTE SELECT input selects the byte of the position data
to be presented at the data output DB1 to DB8. The least sig-
nificant byte will be presented on data output DB9 to DB16
(with the
ENABLE
input taken to a logic “LO”) regardless of
the state of the BYTE SELECT pin. Note that when the
AD2S83 is used with a resolution less than 16 bits the unused
data lines are pulled to a logic “LO.” A logic “HI” on the BYTE
SELECT input will present the eight most significant data bits
on data output DB1 and DB8. A logic “LO” will present the
least significant byte on data outputs 1 to 8, i.e., data outputs
1 to 8 will duplicate data outputs 9 to 16.
The operation of the BYTE SELECT has no effect on the con-
version process of the converter.
RIPPLE CLOCK
As the output of the converter passes through the major carry,
i.e., all “1s” to all “0s” or the converse, a positive going edge on
the RIPPLE CLOCK (RC) output is initiated indicating that a
revolution, or a pitch, of the input has been completed.
The minimum pulsewidth of the ripple clock is 300 ns. RIPPLE
CLOCK is normally set high before a BUSY pulse and resets
before the next positive going edge of the next BUSY pulse.
The only exception to this is when DIR changes while the
RIPPLE CLOCK is high. Resetting of the RIPPLE clock will
only occur if the DIR remains stable for two consecutive posi-
tive BUSY pulse edges.
If the AD2S83 is being used in a pitch and revolution counting
application, the ripple and busy will need to be gated to prevent
false decrement or increment (see Figure 2).
RIPPLE CLOCK is unaffected by
INHIBIT
.
+5V
5K1
IN4148
BUSY
IN4148
RIPPLE
CLOCK
2N3904
0V
10k
V
1k
V
+5V
TO COUNTER
(CLOCK)
NOTE: DO NOT USE ABOVE CCT WHEN
INHIBIT
IS LOW.
Figure 2. Diode Transistor Logic Nand Gate
相關PDF資料 |
PDF描述 |
|---|---|
| AD2S90 | Low Cost, Complete 12-Bit Resolver-to-Digital Converter |
| AD2S90AP | Low Cost, Complete 12-Bit Resolver-to-Digital Converter |
| AD2S93 | Low Cost LVDT-to-Digital Converter |
| AD2S93AP | Aluminum Electrolytic Capacitor; Capacitor Type:Industrial Grade; Voltage Rating:350VDC; Capacitor Dielectric Material:Aluminum Electrolytic; Operating Temperature Range:-40 C to +85 C; Capacitance:160uF RoHS Compliant: Yes |
| AD2S93BP | Aluminum Electrolytic Capacitor; Capacitor Type:Industrial Grade; Voltage Rating:150VDC; Capacitor Dielectric Material:Aluminum Electrolytic; Operating Temperature Range:-40 C to +85 C; Capacitance:16uF RoHS Compliant: Yes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD2S83AP | 制造商:Analog Devices 功能描述:Resolver to Digital 16-Bit Parallel ±8arcmin 44-Pin PLCC 制造商:Analog Devices 功能描述:RESOLVER TO DGTL CNVRTR 44PLCC - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:8 ARC MIN 44PLCC -40/85C - Bulk 制造商:Analog Devices 功能描述:IC R/D CONVERTER 10-16 BIT |
| AD2S83APZ | 功能描述:IC R/D CONV TRACKING 44PLCC RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD2S83APZ-REEL | 功能描述:IC CONV R/D MONO VAR RES 44PLCC RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD2S83IP | 制造商:Analog Devices 功能描述:Resolver to Digital 16-Bit Parallel 制造商:Analog Devices 功能描述:RESOLVER TO DGTL CNVRTR 44PLCC - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:8 ARC MIN 44PLCC -40/85C - Bulk |
| AD2S83IP-REEL | 制造商:Analog Devices 功能描述:Resolver to Digital 16-Bit Parallel 制造商:Rochester Electronics LLC 功能描述:8 ARC MIN 44PLCC -40/85C - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。