- 您現在的位置：買賣IC網 > PDF目錄373867 > AD2S83 (Analog Devices, Inc.) Variable Resolution, Monolithic Resolver-to-Digital Converters(可變分辨率,單片解算-數字變換器) PDF資料下載
參數資料
| 型號： | AD2S83 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Variable Resolution, Monolithic Resolver-to-Digital Converters(可變分辨率,單片解算-數字變換器) |
| 中文描述： | 可變分辨率，單片分解到數字轉換器（可變分辨率，單片解算-數字變換器） |
| 文件頁數： | 14/19頁 |
| 文件大?。?/td> | 198K |
| 代理商： | AD2S83 |
AD2S83
REV. D
–14–
The small signal step response is shown in Figure 7. The time
from the step to the first peak is t
1
, and the t
2
is the time from
the step until the converter is settled to 1 LSB. The times t
1
and
t
2
are given approximately by
t
1
=
1
f
BW
5
f
BW
t
2
=
×
R
12
where R = resolution, i.e., 10, 12, 14 or 16.
t
2
t
1
TIME
Figure 7. Small Step Response
The large signal step response (for steps greater than 5 degrees)
applies when the error voltage exceeds the linear range of the
converter.
Typically the converter will take three times longer to reach the
first peak for a 179 degrees step.
In response to a velocity step, the velocity output will exhibit
the same time response characteristics as outlined above for the
position output.
THE AD2S83 AS A SILICON TACHOGENERATOR
Position Control Using the AD2S83
The AD2S83 has been optimized for use as a feedback device
for velocity as well as position. A traditional position control
loop shown below compares a demand position with an actual
to derive a position error and hence a velocity demand.
+
–
POSITION
DEMAND
ACTUAL
POSITION
MOTOR
FEEDBACK
SOURCE
CONTROL
TERMS
POSITION
ELECTRONICS
Figure 8. Position Control
Quality of control may be reduced if the load on a motor varies
dynamically. System reaction and compensation for a sudden
change in the loading depends on how rapidly the system can
update the velocity demand to the motor. This can cause rapid
acceleration of the motor until the loop updates with a new
velocity demand.
The only effective way to compensate for dynamic loading
effects is to introduce a 2nd order term which will provide the
motor with an acceleration or deceleration demand signal (see
Figure 9).
CONTROL
TERMS
POSITION
ELECTRONICS
+
–
POSITION
DEMAND
ACTUAL
POSITION
MOTOR
FEEDBACK
SOURCE
VELOCITY
ELECTRONICS
Figure 9. Position Control and Velocity Control
Traditionally this would need to be implemented by using sepa-
rate position and speed feedback transducers, e.g., an encoder
or resolver and a dc tachogenerator. The AD2S83 can decode
the resolver to provide both velocity and position information.
DC Tachogenerator
The DC tachogenerator is a small permanent magnet dc
generator. The output is a dc voltage which is proportional to
the speed of the rotor and whose polarity is determined by the
direction of rotation. Physically they are similar to a resolver.
Velocity Error Derivation
The velocity error is the difference between the synthesized dc
velocity demand derived from the actual and demand positions
and the feedback from the tachogenerator or the AD2S83. The
velocity demand is usually derived via a DAC so apart from any
quantization noise it is clean. The velocity feedback, therefore,
needs to be as close to a pure dc level as possible. The errors
which determine the quality of the resultant acceleration de-
mand to the motor are explained below.
Linearity
Linearity is the maximum deviation from the ideal straight line
velocity characteristic. The line used is given by:
v
=
mx
+
c
where
v
= velocity
m
= gain scaling
x
= dc voltage
c
= zero velocity dc offset
Linearity is generally a function of the input velocity to the
tachogenerator or resolver.
Reversion Error
Reversion or reversal error is an offset which is dependent on
the direction of rotation of the transducer; e.g., if 10 rps =
1.000 V dc, then –10 rps = 1.003 V dc with +0.3% reversion
error and FSO =
±
8 V dc.
Zero Velocity DC Offset
This is a residual dc offset present at zero input velocity. This
can be externally nulled.
相關PDF資料 |
PDF描述 |
|---|---|
| AD2S90 | Low Cost, Complete 12-Bit Resolver-to-Digital Converter |
| AD2S90AP | Low Cost, Complete 12-Bit Resolver-to-Digital Converter |
| AD2S93 | Low Cost LVDT-to-Digital Converter |
| AD2S93AP | Aluminum Electrolytic Capacitor; Capacitor Type:Industrial Grade; Voltage Rating:350VDC; Capacitor Dielectric Material:Aluminum Electrolytic; Operating Temperature Range:-40 C to +85 C; Capacitance:160uF RoHS Compliant: Yes |
| AD2S93BP | Aluminum Electrolytic Capacitor; Capacitor Type:Industrial Grade; Voltage Rating:150VDC; Capacitor Dielectric Material:Aluminum Electrolytic; Operating Temperature Range:-40 C to +85 C; Capacitance:16uF RoHS Compliant: Yes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD2S83AP | 制造商:Analog Devices 功能描述:Resolver to Digital 16-Bit Parallel ±8arcmin 44-Pin PLCC 制造商:Analog Devices 功能描述:RESOLVER TO DGTL CNVRTR 44PLCC - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:8 ARC MIN 44PLCC -40/85C - Bulk 制造商:Analog Devices 功能描述:IC R/D CONVERTER 10-16 BIT |
| AD2S83APZ | 功能描述:IC R/D CONV TRACKING 44PLCC RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD2S83APZ-REEL | 功能描述:IC CONV R/D MONO VAR RES 44PLCC RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD2S83IP | 制造商:Analog Devices 功能描述:Resolver to Digital 16-Bit Parallel 制造商:Analog Devices 功能描述:RESOLVER TO DGTL CNVRTR 44PLCC - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:8 ARC MIN 44PLCC -40/85C - Bulk |
| AD2S83IP-REEL | 制造商:Analog Devices 功能描述:Resolver to Digital 16-Bit Parallel 制造商:Rochester Electronics LLC 功能描述:8 ARC MIN 44PLCC -40/85C - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。