- 您現在的位置：買賣IC網 > PDF目錄373867 > AD2S83 (Analog Devices, Inc.) Variable Resolution, Monolithic Resolver-to-Digital Converters(可變分辨率,單片解算-數字變換器) PDF資料下載
參數資料
| 型號： | AD2S83 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Variable Resolution, Monolithic Resolver-to-Digital Converters(可變分辨率,單片解算-數字變換器) |
| 中文描述： | 可變分辨率，單片分解到數字轉換器（可變分辨率，單片解算-數字變換器） |
| 文件頁數： | 16/19頁 |
| 文件大?。?/td> | 198K |
| 代理商： | AD2S83 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁
AD2S83
REV. D
–16–
SOURCES OF ERRORS
Integrator Offset
Additional inaccuracies in the conversion of the resolver signals
will result from an offset at the input to the integrator. This
offset will be treated as an error signal. The resulting angular
error will typically be 1 arc minute over the operating tempera-
ture range.
A description of how to adjust the zero offset is given in the
Component Selection section; the circuit required is shown in
Figure 1.
Differential Phase Shift
Phase shift between the sine and cosine signals from the resolver
is known as differential phase shift and can cause static error.
Some differential phase shift will be present on all resolvers as a
result of coupling. A small resolver residual voltage (quadrature
voltage) indicates a small differential phase shift. Additional
phase shift can be introduced if the sine channel wires and the
cosine channel wires are treated differently. For instance, differ-
ent cable lengths or different loads could cause differential phase
shift.
The additional error caused by differential phase shift on the
input signals approximates to
Error =
0.53
a
×
b arc minutes
where a = differential phase shift (degrees).
b = signal to reference phase shift (degrees).
This error can be minimized by choosing a resolver with a small
residual voltage, ensuring that the sine and cosine signals are
handled identically and removing the reference phase shift (see
the Connecting the Resolver section). By taking these precau-
tions the extra error can be made insignificant.
Most resolvers exhibit a phase shift between the signal and the
reference. This phase shift will, however, give rise under dy-
namic conditions to an additional error defined by:
Shaft Speed
(
rps
)
×
Phase Shift
(
Degrees
)
Reference Frequency
=
Error Degrees
Under static operating conditions phase shift between the refer-
ence and the signal lines alone will not theoretically affect the
converter’s static accuracy.
For example, for a phase shift of 20 degrees, a shaft rotation of
22 rps and a reference frequency of 5 kHz, the converter will
exhibit an additional error of:
22
×
20
=
0.088
Degrees
5000
This effect can be eliminated by placing a phase shift in the
reference to the converter equivalent to the phase shift in the
resolver (see the Connecting the Resolver section).
Note: Capacitive and inductive crosstalk in the signal and reference
leads and wiring can cause similar problems
.
VELOCITY ERRORS
Some “ripple” or noise will always be present in the velocity
signal. Velocity signal ripple is caused by, or related to, the
following parameters. The resulting effects are generally addi-
tive. This means diagnosis needs to be an iterative process in
order to define the source of the error.
1.0 Reference Frequency
A ripple content at the reference frequency is superimposed
on the velocity signal output. The amplitude depends on
the loop bandwidth. This error is a function of a dc offset at
the input to Phase Sensitive Demodulator (PSD).
2.0 Resolver Inaccuracies
Impedance mismatch occur in the sine and cosine windings
of the resolver. These give rise to differential phase shift
between the sine and cosine inputs to the RDC and varia-
tions in the resolver output amplitudes.
2.1 Sine and Cosine Amplitude Mismatch
This is normally identified by the presence of asymmetrical
ripple voltages.
2.2 Differential Phase Shift between the Sine and Cosine Inputs
The frequency of this ripple is usually twice the input veloc-
ity, and the amplitude is proportional to the magnitude of
the velocity signal. The phase shift is normally induced
through the connections from the resolver to the converter.
Maintaining equal lengths of screened twisted pair cable
from the resolver to the AD2S83 will reduce the effects of
resistive imbalance, and therefore, reduce differential phase
shift.
3.0 LSB Update Ripple
LSB update noise occurs as the resolver rotates and the
digital outputs of the RDC are updated. For a correctly
scaled loop, this ripple component has a magnitude of
approximately 2 mV peak at 16-bit resolution.
3.1 Ripple due to the LSB rate given by:
LSB rate = N
×
Reference Frequency
The PSD generates sums and differences of all its compo-
nent input frequencies, so when the LSB update rate is an
multiple of the reference frequency, a beat frequency is
generated. The magnitude of this ripple is a function of the
LSB weighting, i.e., ripple is less at 16 bits.
4.0 Torque Ripple
Torque ripple is a phenomenon associated with motors. An
ac motor naturally exhibits a sinusoidal back emf. In an
ideal system the current fed to the motor should, in order
to cancel, also be sinusoidal. In practice the current is often
trapezoidal. Consequently, the output torque from the
motor will not be smooth and torque ripple is created. If
the loading on a motor is constant, the velocity of the mo-
tor shaft will vary as a result of the cyclic variation of motor
torque. The variation in velocity then appears on the veloc-
ity output as ripple. This is not an error but a true velocity
variation in the system.
相關PDF資料 |
PDF描述 |
|---|---|
| AD2S90 | Low Cost, Complete 12-Bit Resolver-to-Digital Converter |
| AD2S90AP | Low Cost, Complete 12-Bit Resolver-to-Digital Converter |
| AD2S93 | Low Cost LVDT-to-Digital Converter |
| AD2S93AP | Aluminum Electrolytic Capacitor; Capacitor Type:Industrial Grade; Voltage Rating:350VDC; Capacitor Dielectric Material:Aluminum Electrolytic; Operating Temperature Range:-40 C to +85 C; Capacitance:160uF RoHS Compliant: Yes |
| AD2S93BP | Aluminum Electrolytic Capacitor; Capacitor Type:Industrial Grade; Voltage Rating:150VDC; Capacitor Dielectric Material:Aluminum Electrolytic; Operating Temperature Range:-40 C to +85 C; Capacitance:16uF RoHS Compliant: Yes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD2S83AP | 制造商:Analog Devices 功能描述:Resolver to Digital 16-Bit Parallel ±8arcmin 44-Pin PLCC 制造商:Analog Devices 功能描述:RESOLVER TO DGTL CNVRTR 44PLCC - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:8 ARC MIN 44PLCC -40/85C - Bulk 制造商:Analog Devices 功能描述:IC R/D CONVERTER 10-16 BIT |
| AD2S83APZ | 功能描述:IC R/D CONV TRACKING 44PLCC RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD2S83APZ-REEL | 功能描述:IC CONV R/D MONO VAR RES 44PLCC RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD2S83IP | 制造商:Analog Devices 功能描述:Resolver to Digital 16-Bit Parallel 制造商:Analog Devices 功能描述:RESOLVER TO DGTL CNVRTR 44PLCC - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:8 ARC MIN 44PLCC -40/85C - Bulk |
| AD2S83IP-REEL | 制造商:Analog Devices 功能描述:Resolver to Digital 16-Bit Parallel 制造商:Rochester Electronics LLC 功能描述:8 ARC MIN 44PLCC -40/85C - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。