- 您現在的位置：買賣IC網 > PDF目錄373867 > AD2S80AUD (ANALOG DEVICES INC) Variable Resolution, Monolithic Resolver-to-Digital Converter PDF資料下載
參數資料
| 型號： | AD2S80AUD |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 位置變換器 |
| 英文描述： | Variable Resolution, Monolithic Resolver-to-Digital Converter |
| 中文描述： | SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, CDIP40 |
| 封裝： | SIDE BRAZED, CERAMIC, DIP-40 |
| 文件頁數： | 7/16頁 |
| 文件大?。?/td> | 268K |
| 代理商： | AD2S80AUD |
AD2S80A
REV. A
–7–
CONVE RT E R OPE RAT ION
When connected in a circuit such as shown in Figure 1 the
AD2S80A operates as a tracking resolver-to-digital converter
and forms a T ype 2 closed-loop system. T he output will auto-
matically follow the input for speeds up to the selected maxi-
mum tracking rate. No convert command is necessary as the
conversion is automatically initiated by each LSB increment, or
decrement, of the input. Each LSB change of the converter ini-
tiates a BUSY pulse.
T he AD2S80A is remarkably tolerant of input amplitude and
frequency variation because the conversion depends only on the
ratio of the input signals. Consequently there is no need for ac-
curate, stable oscillator to produce the reference signal. T he in-
clusion of the phase sensitive detector in the conversion loop
ensures a high immunity to signals that are not coherent or are
in quadrature with the reference signal.
SIGNAL CONDIT IONING
T he amplitude of the SINE and COSINE signal inputs should
be maintained within 10% of the nominal values if full perfor-
mance is required from the velocity signal.
T he digital position output is relatively insensitive to amplitude
variation. Increasing the input signal levels by more than 10%
will result in a loss in accuracy due to internal overload. Reduc-
ing levels will result in a steady decline in accuracy. With the
signal levels at 50% of the correct value, the angular error will
increase to an amount equivalent to 1.3 LSB. At this level the
repeatability will also degrade to 2 LSB and the dynamic re-
sponse will also change, since the dynamic characteristics are
proportional to the signal level.
T he AD2S80A will not be damaged if the signal inputs are
applied to the converter without the power supplies and/or the
reference.
RE FE RE NCE INPUT
T he amplitude of the reference signal applied to the converter’s
input is not critical, but care should be taken to ensure it is kept
within the recommended operating limits.
T he AD2S80A will not be damaged if the reference is supplied
to the converter without the power supplies and/or the signal
inputs.
HARMONIC DIST ORT ION
T he amount of harmonic distortion allowable on the signal and
reference lines is 10%.
Square waveforms can be used but the input levels should be
adjusted so that the average value is 1.9 V rms. (For example, a
square wave should be 1.9 V peak.) T riangular and sawtooth
waveforms should have a amplitude of 2 V rms.
Note: T he figure specified of 10% harmonic distortion is for
calibration convenience only.
POSIT ION OUT PUT
T he resolver shaft position is represented at the converter out-
put by a natural binary parallel digital word. As the digital posi-
tion output of the converter passes through the major carries,
i.e., all “1s” to all “0s” or the converse, a RIPPLE CLOCK
(RC) logic output is initiated indicating that a revolution or a
pitch of the input has been completed.
T he direction of input rotation is indicated by the DIRECT ION
(DIR) logic output. T his direction data is always valid in ad-
vance of a RIPPLE CLOCK pulse and, as it is internally
latched, only changing state (1 LSB min change) with a corre-
sponding change in direction.
Both the RIPPLE CLOCK pulse and the DIRECT ION data
are unaffected by the application of the
INHIBIT
. T he static
positional accuracy quoted is the worst case error that can occur
over the full operating temperature excluding the effects of off-
set signals at the INT EGRAT OR INPUT (which can be
trimmed out—see Figure 1), and with the following conditions:
input signal amplitudes are within 10% of the nominal; phase
shift between signal and reference is less than 10 degrees.
T hese operating conditions are selected primarily to establish a
repeatable acceptance test procedure which can be traced to na-
tional standards. In practice, the AD2S80A can be used well
outside these operating conditions providing the above points
are observed.
VE LOCIT Y SIGNAL
T he tracking converter technique generates an internal signal at
the output of the integrator (the INT EGRAT OR OUT PUT
pin) that is proportional to the rate of change of the input angle.
T his is a dc analog output referred to as the VELOCIT Y signal.
In many applications it is possible to use the velocity signal of
the AD2S80A to replace a conventional tachogenerator.
DC E RROR SIGNAL
T he signal at the output of the phase sensitive detector (DE-
MODULAT OR OUT PUT ) is the signal to be nulled by the
tracking loop and is, therefore, proportional to the error be-
tween the input angle and the output digital angle. T his is the
dc error of the converter; and as the converter is a T ype 2 servo
loop, it will increase if the output fails to track the input for any
reason. It is an indication that the input has exceeded the maxi-
mum tracking rate of the converter or, due to some internal
malfunction, the converter is unable to reach a null. By connect-
ing two external comparators, this voltage can be used as a
“built-in-test.”
相關PDF資料 |
PDF描述 |
|---|---|
| AD2S80AUE | Variable Resolution, Monolithic Resolver-to-Digital Converter |
| AD2S81A | Variable Resolution, Monolithic Resolver-to-Digital Converters(可變分辨率,單片R/D變換器) |
| AD2S82A | Variable Resolution, Monolithic Resolver-to-Digital Converters(可變分辨率,單片解算-數字變換器) |
| AD2S82AJP | Circular Connector; No. of Contacts:16; Series:MS27473; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:20; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:20-16 RoHS Compliant: No |
| AD2S82AHP | Variable Resolution, Monolithic Resolver-to-Digital Converters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD2S80AUD/B | 制造商:Analog Devices 功能描述:2 ARC MIN HIREL MIL TEMP - Bulk |
| AD2S80AUE | 制造商:AD 制造商全稱:Analog Devices 功能描述:Variable Resolution, Monolithic Resolver-to-Digital Converter |
| AD2S80SD | 制造商:Analog Devices 功能描述: |
| AD2S81 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Variable Resolution, Monolithic Resolver-to-Digital Converters |
| AD2S81A | 制造商:AD 制造商全稱:Analog Devices 功能描述:Variable Resolution, Monolithic Resolver-to-Digital Converters |
發布緊急采購，3分鐘左右您將得到回復。