- 您現在的位置：買賣IC網 > PDF目錄381233 > AAT2556 (Advanced Analog Technology,lnc.) Battery Charger and Step-Down Converter for Portable Applications PDF資料下載
參數資料
| 型號： | AAT2556 |
| 廠商： | Advanced Analog Technology,lnc. |
| 英文描述： | Battery Charger and Step-Down Converter for Portable Applications |
| 中文描述： | 電池充電器和降壓轉換器為便攜式應用 |
| 文件頁數： | 22/29頁 |
| 文件大?。?/td> | 708K |
| 代理商： | AAT2556 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
AAT2556
Battery Charger and Step-Down
Converter for Portable Applications
22
2556.2006.09.1.2
Printed Circuit Board Layout
Considerations
For the best results, it is recommended to physi-
cally place the battery pack as close as possible to
the AAT2556 BAT pin. To minimize voltage drops
on the PCB, keep the high current carrying traces
adequately wide. Refer to the AAT2556 evaluation
board for a good layout example (see Figures 6
and 7). The following guidelines should be used to
help ensure a proper layout.
1. The input capacitors (C1, C3) should connect
as closely as possible to ADP (Pin 9) and VIN
(Pin 12).
2. C4 and L1 should be connected as closely as
possible. The connection of L1 to the LX pin
should be as short as possible. Do not make the
node small by using narrow trace. The trace
should be kept wide, direct, and short.
3. The feedback pin (Pin 1) should be separate
from any power trace and connect as closely as
possible to the load point. Sensing along a high-
current load trace will degrade DC load regula-
tion. Feedback resistors should be placed as
closely as possible to the FB pin (Pin 1) to mini-
mize the length of the high impedance feedback
trace. If possible, they should also be placed
away from the LX (switching node) and inductor
to improve noise immunity.
4. The resistance of the trace from the load return
to PGND (Pin 10) and GND (Pin 2) should be
kept to a minimum. This will help to minimize any
error in DC regulation due to differences in the
potential of the internal signal ground and the
power ground.
5. A high density, small footprint layout can be
achieved using an inexpensive, miniature, non-
shielded, high DCR inductor.
Figure 6: AAT2556 Evaluation Board
Top Side Layout.
Figure 7: AAT2556 Evaluation Board
Bottom Side Layout.
相關PDF資料 |
PDF描述 |
|---|---|
| AAT2556IWP-CA-T1 | Battery Charger and Step-Down Converter for Portable Applications |
| AAT2803 | Six-Channel White LED Backlight Charge Pump with Flash |
| AAT2803ISK-4.5-T1 | Six-Channel White LED Backlight Charge Pump with Flash |
| AAT3110IGU-4.5-T1 | MicroPower⑩ Regulated Charge Pump |
| AAT3110IGU-5.0-T1 | MicroPower⑩ Regulated Charge Pump |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AAT2556IWP-CA-T1 | 制造商:AAT 制造商全稱:AAT 功能描述:Battery Charger and Step-Down Converter for Portable Applications |
| AAT2557 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:500mA Battery Charger and 300mA LDO Regulator for Portable Systems |
| AAT2557ITO-CT-T1 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:500mA Battery Charger and 300mA LDO Regulator for Portable Systems |
| AAT2557ITO-CW-T1 | 功能描述:電池管理 500 mA Battery Chrg 300 mA LDO Reg RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| AAT2601 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:Total Power Solution for Portable Applications |
發布緊急采購，3分鐘左右您將得到回復。