- 您現在的位置：買賣IC網 > PDF目錄381233 > AAT2556 (Advanced Analog Technology,lnc.) Battery Charger and Step-Down Converter for Portable Applications PDF資料下載
參數資料
| 型號： | AAT2556 |
| 廠商： | Advanced Analog Technology,lnc. |
| 英文描述： | Battery Charger and Step-Down Converter for Portable Applications |
| 中文描述： | 電池充電器和降壓轉換器為便攜式應用 |
| 文件頁數： | 20/29頁 |
| 文件大小： | 708K |
| 代理商： | AAT2556 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
AAT2556
Battery Charger and Step-Down
Converter for Portable Applications
20
2556.2006.09.1.2
low temperature operation applications, a 10μF
(X5R, X7R) ceramic capacitor is recommended to
stabilize extreme pulsed load conditions.
The output voltage droop due to a load transient is
dominated by the capacitance of the ceramic out-
put capacitor. During a step increase in load cur-
rent, the ceramic output capacitor alone supplies
the load current until the loop responds. Within two
or three switching cycles, the loop responds and
the inductor current increases to match the load
current demand. The relationship of the output volt-
age droop during the three switching cycles to the
output capacitance can be estimated by:
Once the average inductor current increases to the
DC load level, the output voltage recovers. The
above equation establishes a limit on the minimum
value for the output capacitor with respect to load
transients.
The internal voltage loop compensation also limits
the minimum output capacitor value to 4.7μF. This
is due to its effect on the loop crossover frequency
(bandwidth), phase margin, and gain margin.
Increased output capacitance will reduce the
crossover frequency with greater phase margin.
The maximum output capacitor RMS ripple current
is given by:
Dissipation due to the RMS current in the ceram-
ic output capacitor ESR is typically minimal,
resulting in less than a few degrees rise in hot-
spot temperature.
Inductor Selection
The step-down converter uses peak current mode
control with slope compensation to maintain stabil-
ity for duty cycles greater than 50%. The output
inductor value must be selected so the inductor
current down slope meets the internal slope com-
pensation requirements. The internal slope com-
pensation for the AAT2556 is 0.45A/μsec. This
equates to a slope compensation that is 75% of the
inductor current down slope for a 1.8V output and
3.0μH inductor.
For most designs, the step-down converter operates
with an inductor value of 1μH to 4.7μH. Table 3 dis-
plays inductor values for the AAT2556 with different
output voltage options.
Manufacturer's specifications list both the inductor
DC current rating, which is a thermal limitation, and
the peak current rating, which is determined by the
saturation characteristics. The inductor should not
show any appreciable saturation under normal load
conditions. Some inductors may meet the peak and
average current ratings yet result in excessive loss-
es due to a high DCR. Always consider the losses
associated with the DCR and its effect on the total
converter efficiency when selecting an inductor.
The 3.0μH CDRH2D09 series inductor selected
from Sumida has a 150m
Ω
DCR and a 470mA DC
current rating. At full load, the inductor DC loss is
9.375mW which gives a 2.08% loss in efficiency for
a 250mA, 1.8V output.
Table 3: Inductor Values.
Output Voltage (V)
L1 (μH)
1.0
1.2
1.5
1.8
2.5
3.0
3.3
1.5
2.2
2.7
3.0/3.3
3.9/4.2
4.7
5.6
0.75
V
L = = 0.75
≈
1.67
V
O
m
0.45A
V
O
μsec
A
A
μsec
0.75
V
L
m = = 0.75
1.8V
3.0μH
A
μsec
1
2
3
V
OUT
· (V
IN(MAX)
- V
OUT
)
L
·
F
S
·
V
IN(MAX)
RMS(MAX)
I
=
·
·
C
OUT
=
3
·
Δ
I
LOAD
V
DROOP
·
F
S
相關PDF資料 |
PDF描述 |
|---|---|
| AAT2556IWP-CA-T1 | Battery Charger and Step-Down Converter for Portable Applications |
| AAT2803 | Six-Channel White LED Backlight Charge Pump with Flash |
| AAT2803ISK-4.5-T1 | Six-Channel White LED Backlight Charge Pump with Flash |
| AAT3110IGU-4.5-T1 | MicroPower⑩ Regulated Charge Pump |
| AAT3110IGU-5.0-T1 | MicroPower⑩ Regulated Charge Pump |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AAT2556IWP-CA-T1 | 制造商:AAT 制造商全稱:AAT 功能描述:Battery Charger and Step-Down Converter for Portable Applications |
| AAT2557 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:500mA Battery Charger and 300mA LDO Regulator for Portable Systems |
| AAT2557ITO-CT-T1 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:500mA Battery Charger and 300mA LDO Regulator for Portable Systems |
| AAT2557ITO-CW-T1 | 功能描述:電池管理 500 mA Battery Chrg 300 mA LDO Reg RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| AAT2601 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:Total Power Solution for Portable Applications |
發布緊急采購，3分鐘左右您將得到回復。