參數資料
型號： AAT2556
廠商： Advanced Analog Technology,lnc.
英文描述： Battery Charger and Step-Down Converter for Portable Applications
中文描述： 電池充電器和降壓轉換器為便攜式應用
文件頁數： 17/29頁
文件大?。?/td> 708K
代理商： AAT2556
The LED should be biased with as little current as
necessary to create reasonable illumination; there-
fore, a ballast resistor should be placed between
the LED cathode and the STAT pin. LED current
consumption will add to the overall thermal power
budget for the device package, hence it is good to
keep the LED drive current to a minimum. 2mA
should be sufficient to drive most low-cost green or
red LEDs. It is not recommended to exceed 8mA
for driving an individual status LED.
The required ballast resistor values can be esti-
mated using the following formulas:
Example:
Note: Red LED forward voltage (V
F
) is typically
2.0V @ 2mA.
Thermal Considerations
The AAT2556 is offered in a TDFN33-12 package
which can provide up to 2W of power dissipation
when it is properly bonded to a printed circuit board
and has a maximum thermal resistance of 50°C/W.
Many considerations should be taken into account
when designing the printed circuit board layout, as
well as the placement of the charger IC package in
proximity to other heat generating devices in a
given application design. The ambient temperature
around the IC will also have an effect on the ther-
mal limits of a battery charging application. The
maximum limits that can be expected for a given
ambient condition can be estimated by the follow-
ing discussion.
First, the maximum power dissipation for a given
situation should be calculated:
Where:
P
D(MAX)
= Maximum Power Dissipation (W)
θ
JA
= Package Thermal Resistance (°C/W)
T
J(MAX)
= Maximum Device Junction Temperature
(°C) [135°C]
T
A
Figure 3 shows the relationship of maximum
power dissipation and ambient temperature of the
AAT2556.
= Ambient Temperature (°C)
Figure 3: Maximum Power Dissipation.
Next, the power dissipation of the battery charger
can be calculated by the following equation:
Where:
P
D
V
ADP
= ADP/USB Voltage
V
BAT
= Battery Voltage as Seen at the BAT Pin
I
CH
= Constant Charge Current Programmed for
the Application
= Total Power Dissipation by the Device
I
OP
= Quiescent Current Consumed by the
Charger IC for Normal Operation [0.5mA]
By substitution, we can derive the maximum
charge current before reaching the thermal limit
condition (thermal cycling). The maximum charge
current is the key factor when designing battery
charger applications.
P
D
= [(V
ADP
- V
BAT
)
·
I
CH
+ (V
ADP
·
I
OP
)]
T
A
(
°
C)
P
D
0
500
1000
1500
2000
2500
3000
0
20
40
60
80
100
120
(T
J(MAX)
-
T
A
)
θ
JA
P
D(MAX)
=
(5.5V
- 2.0
V)
2mA
R
1
=
= 1.75k
Ω
(V
ADP
-
V
F(LED)
)
I
LED
R
1
=
AAT2556
Battery Charger and Step-Down
Converter for Portable Applications
2556.2006.09.1.2
17
相關PDF資料
PDF描述
AAT2556IWP-CA-T1 Battery Charger and Step-Down Converter for Portable Applications
AAT2803 Six-Channel White LED Backlight Charge Pump with Flash
AAT2803ISK-4.5-T1 Six-Channel White LED Backlight Charge Pump with Flash
AAT3110IGU-4.5-T1 MicroPower⑩ Regulated Charge Pump
AAT3110IGU-5.0-T1 MicroPower⑩ Regulated Charge Pump
相關代理商/技術參數
參數描述
AAT2556IWP-CA-T1 制造商:AAT 制造商全稱:AAT 功能描述:Battery Charger and Step-Down Converter for Portable Applications
AAT2557 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:500mA Battery Charger and 300mA LDO Regulator for Portable Systems
AAT2557ITO-CT-T1 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:500mA Battery Charger and 300mA LDO Regulator for Portable Systems
AAT2557ITO-CW-T1 功能描述:電池管理 500 mA Battery Chrg 300 mA LDO Reg RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
AAT2601 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:Total Power Solution for Portable Applications
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*