- 您現在的位置：買賣IC網 > PDF目錄375161 > A8906CLB (Allegro MicroSystems, Inc.) BIDIRECTIONAL 3-PHASE BRUSHLESS DC MOTOR CONTROLLER/DRIVER WITH BACK-EMF SENSING PDF資料下載
參數資料
| 型號： | A8906CLB |
| 廠商： | Allegro MicroSystems, Inc. |
| 英文描述： | BIDIRECTIONAL 3-PHASE BRUSHLESS DC MOTOR CONTROLLER/DRIVER WITH BACK-EMF SENSING |
| 中文描述： | 雙向三相無刷直流電機控制器/返回驅動程序，電磁場遙感 |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 159K |
| 代理商： | A8906CLB |
8906
BIDIRECTIONAL
3-PHASE BRUSHLESS DC
MOTOR CONTROLLER/DRIVER
Serial Port.
The serial port functions to write various operational
and diagnostic modes to the A8906CLB. The serial port DATA IN is
enabled/disabled by the CHIP SELECT terminal. When CHIP SE-
LECT is high the serial port is disabled and the chip is not affected by
changes in data at the DATA IN or CLOCK terminals.
To write data to the serial port, the CLOCK terminal should be low
prior to the CHIP SELECT terminal going low. Once CHIP SELECT
goes low, information on the DATA IN terminal is read into the shift
register on the positive-going transition of the CLOCK. There are 24
bits in the serial input port.
Data written into the serial port is latched and becomes active
upon the low-to-high transition of the CHIP SELECT terminal at the
end of the write cycle. D0 will be the last bit written to the serial port.
SERIAL PORT BIT DEFINITIONS
D0- Sleep/Run Mode; LOW = Sleep, HIGH = Run
This bit allows the device to be powered down when not in use.
D1- Step Mode; LOW = Normal Operation, HIGH = Step Only
When in the step-only mode the back-EMF commutation circuitry
is disabled and the power outputs are commutated by the start-
up oscillator. This mode is intended for device and system
testing.
D2- Direction; LOW = Forward, HIGH = Reverse.
D3 and D4 - These two bits set the output current limit:
D3
D4
Current Limit
0
0
1
1
0
1
0
1
1.2 A
1 A
600 mA
250 mA
D5 thru D18-This 14-bit word (active low) programs the
REF
time to set
desired motor speed.
Bit Number Count Number
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
D16
D17
D18
16
32
64
128
256
512
1 024
2 048
4 096
8 192
16 384
32 768
65 536
131 072
D19-Speed-control mode switch;
LOW = internal once-around speed signal,
HIGH = external sector data.
D20 and D21-These bits program the number
of motor poles for the once-around
FCOM
D20
D21
Motor Poles
0
0
1
1
0
1
0
1
8
4
16
12
D22 and D23-Controls the multiplexer for
DATA OUT:
D22
D23
DATA OUT
0
0
1
1
0
1
0
1
TACH (once around or sector)
Thermal Shutdown
SYNC
FCOM
Reset.
The RESET terminal when pulled
low clears all serial port bits, including the D0
latch, which puts the A8906CLB in the sleep
mode.
相關PDF資料 |
PDF描述 |
|---|---|
| A8909CLB | 3-PHASE BRUSHLESS DC MOTOR CONTROLLER/DRIVER WITH BACK-EMF SENSING AND POWER DMOS OUTPUTS |
| A8920 | Dual Schottky Barrier Diodes(用于硬盤驅動器的20V反向電壓雙肖特基勢壘二極管) |
| A8920SLR | DUAL SCHOTTKY DIODE |
| A8932 | Voice-Coil Motor Driver(音頻線圈電機驅動器) |
| A8936CJT | VOICE COIL MOTOR DRIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A8909CLB | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:3-PHASE BRUSHLESS DC MOTOR CONTROLLER/DRIVER WITH BACK-EMF SENSING AND POWER DMOS OUTPUTS |
| A891 | 制造商:Thomas & Betts 功能描述:FIXTURE FITTING |
| A89120-000 | 制造商:TE Connectivity 功能描述:VARISTOR 82V 7MM STRAIGHT LEAD 制造商:TE Connectivity 功能描述:VARISTOR 82V 1.75KA DISC 7MM 制造商:TE CONNECTIVITY RAYCHEM-POLYSWITCH 功能描述:Var MOV 50VAC 65VDC 1750A 82V Thru-Hole Bulk |
| A89125-000 | 制造商:TE Connectivity 功能描述:VARISTOR 390VDC 7MM 10% LEADED 制造商:TE Connectivity 功能描述:VARISTOR 390V 1.2KA DISC 7MM |
| A89156-000 | 制造商:TE Connectivity 功能描述:Conn Power 制造商:TE Connectivity 功能描述:MTCPQKT2P22PGCC |
發布緊急采購，3分鐘左右您將得到回復。