- 您現在的位置：買賣IC網 > PDF目錄362038 > A8351601SERIES Bar Code Reader PDF資料下載
參數資料
| 型號： | A8351601SERIES |
| 英文描述： | Bar Code Reader |
| 中文描述： | 條碼閱讀器 |
| 文件頁數： | 22/43頁 |
| 文件大?。?/td> | 413K |
| 代理商： | A8351601SERIES |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
A8351601 Series
PRELIMINARY (October, 2001, Version 0.5)
21
AMIC Technology, Inc.
Using Timer 2 to Generate Baud Rates
In the A8351601, setting TCLK and/or RCLK in T2CON
selects Timer 2 as the baud rate generator. Under these
conditions, the baud rates for transmit and receive can be
simultaneously different. Setting RCLK and/or TCLK puts
Timer 2 into its baud rate generator mode, as shown in
Figure 8.
The baud rate generator mode is similar to the auto-reload
mode, in that a rollover in TH2 reloads the Timer 2
registers with the 16-bit value in the RCAP2H and RCAP2L
registers, which are preset by software.
In this case, the baud rates in Mode 1 and 3 are
determined by the Timer 2 overflow rate according to the
following Equation.
Timer
Modes 1,3 Baud Rate =
16
Rate
Overflow
Timer 2 can be configured for either timer or counter
operation. In the most typical applications, it is configured
for timer operation (C/
T2
= 0). Normally, a timer increments
every machine cycle (thus at 1/12 the oscillator frequency),
but timer operation is a different for Timer 2 when it is used
as a baud rate generator. As a baud rate generator, Timer
2 increments every state time (thus at 1/2 the oscillator
frequency). In this case, the baud rate is given by the
following formula.
Oscillator
Baud Rate
RCAP2L)]
(RCAP2H,
-
[65536
X
32
Frequency
Where (RCAP2H, RCAP2L) is the content of RCAP2H and
RCAP2L taken as a 16-bit unsigned integer.
Table 9. Commonly Used Baud Rates Generated by Timer 1
Figure 7 shows Timer 2 as a baud rate generator. This
figure is valid only if RCLK + TCLK = 1 in T2CON. A
rollover in TH2 does not set TF2 and does no generate an
interrupt. Therefore, the Timer 2 interrupt does not have to
be disabled when Timer 2 is in the baud rate generator
mode. If EXEN2 is set, a 1-to-0 transition in T2EX sets
EXF2 but does not cause a reload from (RCAP2H,
RCAP2L) to (TH2, TL2). Thus, when Timer 2 is used as a
baud rate generator, T2EX can be used as an extra
external interrupt.
When Timer 2 is running (TR2 = 1) as a timer in the baud
rate generator mode, programmers should not read from or
write to TH2 or TL2. Under these conditions, Timer 2 is
incremented every state time, and the results of a read or
write may not be accurate. The RCAP registers may be
read, but should not be written to, because a write might
overlap a reload and cause write and/or reload errors. Turn
Timer 2 off (clear TR2) before accessing the Timer 2 or
RCAP registers, in this case.
Timer 1
Baud Rate
f
OSC
SMOD
C/
T
X
X
0
0
0
0
0
0
0
0
0
Mode
Reload Value
Mode 0 Max: 1 MHz
Mode 2 Max: 375K
Modes 1,3: 62.5K
19.2K
9.6K
4.8K
2.4K
1.2K
137.5
110
110
12 MHz
12 MHz
12 MHz
11.059 MHz
11.059 MHz
11.059 MHz
11.059 MHz
11.059 MHz
11.986 MHz
6 MHz
12 MHz
X
1
1
1
0
0
0
0
0
0
0
X
X
2
2
2
2
2
2
2
2
1
X
X
FFH
FDH
FDH
FAH
F4H
E8H
1DH
72H
FEEBH
相關PDF資料 |
PDF描述 |
|---|---|
| A8396BH | 16-Bit Microcontroller |
| C8395BH | Single buffer (open drain) |
| LC8395BH | 16-Bit Microcontroller |
| LN8396BH | 16-Bit Microcontroller |
| LP8395BH | 16-Bit Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A83516-12 | 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:8 Bit Microcontroller |
| A83516-24 | 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:8 Bit Microcontroller |
| A83516-40 | 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:8 Bit Microcontroller |
| A83516L-12 | 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:8 Bit Microcontroller |
| A83516L-24 | 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:8 Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。