參數資料
型號： 9202
廠商： 意法半導體
英文描述： Flash Programmable System Devices with 8032 Microcontroller Core
中文描述： 閃存可編程系統設備與8032微控制器內核
文件頁數： 116/175頁
文件大小： 1731K
代理商： 9202
UPSD3254A, UPSD3254BV, UPSD3253B, UPSD3253BV
116/175
Example.
FS0 is valid when the address is in the
range of 8000h to BFFFh, CSBOOT0 is valid from
8000h to 9FFFh, and RS0 is valid from 8000h to
87FFh. Any address in the range of RS0 always
accesses the SRAM. Any address in the range of
CSBOOT0 greater than 87FFh (and less than
9FFFh) automatically addresses secondary Flash
memory segment 0. Any address greater than
9FFFh accesses the primary Flash memory seg-
ment 0. You can see that half of the primary Flash
memory segment 0 and one-fourth of secondary
Flash memory segment 0 cannot be accessed in
this example.
Note:
An equation that defined FS1 to anywhere
in the range of 8000h to BFFFh would not
be valid.
Figure 54 shows the priority levels for all memory
components. Any component on a higher level can
overlap and has priority over any component on a
lower level. Components on the same level must
not
overlap. Level one has the highest priority and
level 3 has the lowest.
Memory Select Configuration in Program and
Data Spaces.
The MCU Core has separate ad-
dress spaces for Program memory and Data
memory. Any of the memories within the PSD
MODULE can reside in either space or both spac-
es. This is controlled through manipulation of the
VM Register that resides in the CSIOP space.
The VM Register is set using PSDsoft Express to
have an initial value. It can subsequently be
changed by the MCU so that memory mapping
can be changed on-the-fly.
For example, you may wish to have SRAM and pri-
mary Flash memory in the Data space at Boot-up,
and secondary Flash memory in the Program
space at Boot-up, and later swap the primary and
secondary Flash memories. This is easily done
with the VM Register by using PSDsoft Express
Configuration to configure it for Boot-up and hav-
ing the MCU change it when desired. Table 88 de-
scribes the VM Register.
Figure 54. Priority Level of Memory and I/O
Components in the PSD MODULE
Table 88. VM Register
Level 1
SRAM, I/O, or
Peripheral I/O
Level 2
Secondary
Non-Volatile Memory
Highest Priority
Lowest Priority
Level 3
Primary Flash Memory
AI02867D
Bit 7
PIO_EN
Bit 6
Bit 5
Bit 4
Primary
FL_Data
Bit 3
Secondary Data
Bit 2
Primary
FL_Code
Bit 1
Secondary Code
Bit 0
SRAM_Code
0 = disable
PIO Mode
not used
not used
0 = RD
can’t
access
Flash
memory
0 = RD can’t
access Secondary
Flash memory
0 = PSEN
can’t
access
Flash
memory
0 = PSEN can’t
access Secondary
Flash memory
0 = PSEN
can’t
access
SRAM
1= enable
PIO Mode
not used
not used
1 = RD
access
Flash
memory
1 = RD access
Secondary Flash
memory
1 = PSEN
access
Flash
memory
1 = PSEN access
Secondary Flash
memory
1 = PSEN
access
SRAM
相關PDF資料
PDF描述
92100 ION VECTOR SYSTEM
92108K IC
53113 IC
53114 Dual/Triple Ultra-Low-Voltage SOT23 µP Supervisory Circuits
53115 IC
相關代理商/技術參數
參數描述
9202 05 00 制造商:Coto Technology 功能描述:Surface mount reed relay 1 pole single
9202 R/B 功能描述:PLUG BANANA STD SET/2 RED/BLK RoHS:是 類別:連接器，互連式 >> 香蕉式和端頭 - 插座，插頭 系列:- 標準包裝:100 系列:PBD 類型:尖頭插孔 類型:母頭 插頭/配接插頭直徑:標準 安裝類型:通孔，水平 端子:焊接 絕緣體:完全絕緣 特點:- 顏色:紅 包裝:散裝 觸點表面涂層:金 觸點材料:- 主體材料:- 線規:- 工作溫度:-25°C ~ 100°C
92020 功能描述:- Power Management Evaluation Board 制造商:vishay dale 系列:- 零件狀態:有效 主要用途:電源管理 嵌入式:- 使用的 IC/零件:- 主要屬性:- 輔助屬性:- 所含物品:板 標準包裝:1
9202000000 功能描述:CASE CARRY LITE 550 制造商:weidmuller 系列:* 零件狀態:在售 標準包裝:1
920-200P-51S 制造商:Amphenol Corporation 功能描述:CONNECTOR - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*