- 您現在的位置：買賣IC網 > PDF目錄2027 > 8375 (3M)SHEETS HARD LAM DISSP WHT 5X12' PDF資料下載
參數資料
| 型號： | 8375 |
| 廠商： | 3M |
| 文件頁數： | 7/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | SHEETS HARD LAM DISSP WHT 5X12' |
| MSDS 材料安全數據表： | 8300 Series Hard Laminate MSDS |
| 標準包裝： | 5 |
| 系列： | 8300 |
| 墊子類型： | 桌子，工作臺卷筒 |
| 形狀： | 矩形 |
| 長度： | 12'（3.66m） |
| 寬： | 5'（1.52m） |
| 厚度： | 0.04"（1.02mm） |
| 顏色： | 白 |
| 材質： | Laminate |
| 特點： | 耗散 |
| 其它名稱： | 05400718636 98079816025 |
1
78-8136-3801-8
2.0
Cleaning and Maintenance
A.
The 3M Rigid Worksurface 8300 Series is readily cleaned with 3M Static Control Worksurface
Mark Remover 8001. It can also be cleaned with warm water and mild detergents. Many commercially
available detergents are suitable, including common household dishwashing liquids.
B.
Nonabrasive, commercially available surface cleaners such as glass cleaners or products similar to
SoftScrub are suitable. Cleaners containing abrasives or strong acids or alkalines should be avoided.
C.
Stains such as those caused by solder flux, varnishes, ink, etc., can be removed with organic solvents
(alcohols, ketones, xylene, mineral spirits). Such stains can also be removed by a twominute exposure
to a 5% hypochlorite bleach (common laundry bleach) followed immediately by a clean water rinse.
D.
The surface should be protected from heat and from cuts and gouges by means of a hot pad and/or
cutting board. 3M Rigid Worksurfaces will not be affected by drops of molten solder, but will blister
if a soldering iron or some other intensely hot object is left on the surface. Blistering will occur at
approximately 400°F (204°C).
E.
ANYTIME THE LAMINATE SURFACE IS CLEANED OR OTHERWISE AFFECTED, THE
ELECTRICAL PERFORMANCE SHOULD BE VERIFIED.
3.0
Repair
A.
Colored paste can be used to visually repair minor defects in the top surface.
B.
Laminate that was adhered with contact adhesive and that lifts from the substrate can be readhered by
applying heat and pressure. A simple method is to place a piece of cloth over the problem area and then
iron it with a household iron.
C.
While most decorative commercial laminate can be recovered with additional laminate by sanding the
existing surface, cleaning it, and reapplying adhesive, this practice will not work well with 3M Static
Dissipative Rigid Worksurface 8300 Series. The 3M laminate is manufactured with a special, tough,
abrasionresistant coating that resists sanding. Therefore, adhesive will not bond well to the surface.
4.0
Troubleshooting Guide
Surface changes
Discoloration
Due to sunlight
Laminate not intended for outdoor use
Keep laminate away from direct
sunlight
Due to chemicals
Avoid prolonged exposure to bleaches,
acids, alkalis
Due to heat
Remove/insulate heat source
Dents/depressions due to substrate
imperfections
Use higherdensity, thicker, or
smoother substrate
Cover at least 80% of the bond
surfaces with adhesive
相關PDF資料 |
PDF描述 |
|---|---|
| 8812 | TABLE MAT GREEN |
| 91070 | WRIST STRAP SPEIDEL 6'ANGLE 4MM |
| 91095 | CORD GROUND WS COILED 6' RT ANG |
| 9500 | FLOOR RUNNER ANTI-FATIGUE 3'X 5' |
| 960X/980X | WALL TRANSFORMER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 8375 5X12 | 功能描述:TABLE LAMINATE WHITE 5'X1' 制造商:scs 系列:- 零件狀態:有效 墊類型:桌子，工作臺 形狀:矩形 長度:5'（1.52m） 寬度:1'（0.30m） 厚度:0.039"（0.99mm） 顏色:白 材料:層壓 特性:- 包括:- 標準包裝:5 |
| 83-750 | 功能描述:RF 連接器 STRT PLG 59/62/9209 8241 8279 UG-111/U RoHS:否 制造商:Bomar Interconnect 產品:Connectors 射頻系列:BNC 型式:Jack (Female) 極性: 觸點電鍍:Gold 阻抗: 端接類型:Solder 主體類型:Straight Bulkhead 電纜類型: |
| 83-750 (UG-111/U) | 制造商:Amphenol RF 功能描述:RF/COAXIAL UHF PLUG STRAIGHT SOLDER 制造商:Amphenol RF 功能描述:RF/COAXIAL, UHF PLUG, STRAIGHT, SOLDER 制造商:Amphenol RF 功能描述:RF/COAXIAL, UHF PLUG, STRAIGHT, SOLDER; Series:-; Connector Type:UHF Coaxial; Body Style:Straight Plug; Coaxial Termination:Solder; Coaxial Cable Types:RG59, RG62, RG140, RG210; Contact Material:Brass; Contact Plating:Silver ;RoHS Compliant: Yes |
| 8375-1032-A-0 | 制造商:RAF Electronic Hardware 功能描述: |
| 83751-3 | 制造商:TE CONNECTIVITY 功能描述:WRENCH-LOK 350-350, 500-4 TE ENERGY |
發布緊急采購，3分鐘左右您將得到回復。