- 您現在的位置：買賣IC網 > PDF目錄2027 > 8375 (3M)SHEETS HARD LAM DISSP WHT 5X12' PDF資料下載
參數資料
| 型號： | 8375 |
| 廠商： | 3M |
| 文件頁數： | 14/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | SHEETS HARD LAM DISSP WHT 5X12' |
| MSDS 材料安全數據表： | 8300 Series Hard Laminate MSDS |
| 標準包裝： | 5 |
| 系列： | 8300 |
| 墊子類型： | 桌子，工作臺卷筒 |
| 形狀： | 矩形 |
| 長度： | 12'（3.66m） |
| 寬： | 5'（1.52m） |
| 厚度： | 0.04"（1.02mm） |
| 顏色： | 白 |
| 材質： | Laminate |
| 特點： | 耗散 |
| 其它名稱： | 05400718636 98079816025 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁
7
78-8136-3801-8
C.
“Gator Ply”: a commercially available backing material used as moisture barrier. Gator Ply does not
have the balancing qualities as a phenolic high pressurebacking sheet. For severe environmental
humidity swings, a phenolic backing sheet is recommended to balance the construction.
11.0 Adhesives
Many types of adhesive are available for use in applying laminate. Each type has certain characteristics
that make it more suitable for particular applications. Regardless which adhesive is selected, manufacturers'
recommendations should be followed carefully.
A.
Contact adhesives:
This is the most common type of adhesive used with laminate. It works well on a variety of substrates
and does not require sophisticated equipment for fabrication. The only special equipment needed is a
nip roll capable of applying 5075 lbs. per inch (916 kg/cm) of roll.
1. Pressure is very important for proper lamination regardless of the type of adhesive used, but it is
especially important when using contact adhesives. Solvent entrapment is also important, resulting in
a weak bond and latent delamination failures from the substrate.
2. Contact adhesive is available in both solvent and waterbasted systems. Waterbased adhesives are not
recommended for use on steel or iron substrates.
3. An important application for contact adhesives is postforming. The adhesive does not require long
cure under heat and pressure, and the heat inherent to the postforming operation itself assists in
establishing a firm adhesive bond between the laminate and the substrate.
4. It is recommended that a minimum of 80% of the surface area of both the laminate and the substrate
be covered with the contact adhesive. There is a tendency to apply insufficient adhesive. The result is
that the adhesive bond rill be stronger in some spots than in others, causing stresses in the laminate
that may lead to cracking. For this reason, “spot bonding” of the laminate to the substrate should
never be done. On the other hand, because most contact adhesives are neoprenebased, too much
adhesive can also cause problems like delamination or movement of the adhesive itself.
5. The edges of the substrate surface should be doublecoated with adhesive prior to lamination.
Caution: When applying the second coat around the edges, make sure the first coat is dry
and the solvent had a chance to flash off.
6. Laminate will “move” slightly with varying humidity conditions. Contact adhesives permit this
movement to a greater extent than do thermosetting adhesives.
7. Typical of contact adhesives, it is not possible to lift and reposition the laminate once contact has
been established between the adhesivecoated laminate and substrate.
8. The evaporation of solvent from the contact adhesive has a cooling effect that may cause moisture
to condense on the surface of the adhesive. This is referred to as “blushing” and can cause poor
bonding. “Force drying” the adhesive with hot air should reduce this problem.
NOTE: Flashing off of the solvent is dictated by the humidity in the work environment. High
humidity environments require additional time for this process.
B.
Thermosetting adhesives:
These adhesives require time and/or heat for proper curing. A press is needed to apply pressure while
the adhesive cures; 20 psi (1.41 kg/sq cm) is typical. Most thermosetting adhesives are twopart systems
with a specified “pot life,” i.e., they must be used within a limited amount of time once the two parts are
mixed together.
1. Resorcinol: This is the best adhesive for use in applications where cracking due to humidity variations
may be a problem. Resorcinol is recommended where good resistance to water and heat is required.
2. Epoxy: This adhesive is good for applications calling for gapfilling and low shrinkage. It is primarily
used to bond laminate to metal substrates. Because epoxy adhesives are generally “100% solids”
(solventfree), there is no solvent to flash off and problems related to solvent being trapped in the
substrate do not exist. Like Resorcinol, epoxies are good adhesives for applications in which cracking
due to humidity variations could be a problem.
相關PDF資料 |
PDF描述 |
|---|---|
| 8812 | TABLE MAT GREEN |
| 91070 | WRIST STRAP SPEIDEL 6'ANGLE 4MM |
| 91095 | CORD GROUND WS COILED 6' RT ANG |
| 9500 | FLOOR RUNNER ANTI-FATIGUE 3'X 5' |
| 960X/980X | WALL TRANSFORMER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 8375 5X12 | 功能描述:TABLE LAMINATE WHITE 5'X1' 制造商:scs 系列:- 零件狀態:有效 墊類型:桌子，工作臺 形狀:矩形 長度:5'（1.52m） 寬度:1'（0.30m） 厚度:0.039"（0.99mm） 顏色:白 材料:層壓 特性:- 包括:- 標準包裝:5 |
| 83-750 | 功能描述:RF 連接器 STRT PLG 59/62/9209 8241 8279 UG-111/U RoHS:否 制造商:Bomar Interconnect 產品:Connectors 射頻系列:BNC 型式:Jack (Female) 極性: 觸點電鍍:Gold 阻抗: 端接類型:Solder 主體類型:Straight Bulkhead 電纜類型: |
| 83-750 (UG-111/U) | 制造商:Amphenol RF 功能描述:RF/COAXIAL UHF PLUG STRAIGHT SOLDER 制造商:Amphenol RF 功能描述:RF/COAXIAL, UHF PLUG, STRAIGHT, SOLDER 制造商:Amphenol RF 功能描述:RF/COAXIAL, UHF PLUG, STRAIGHT, SOLDER; Series:-; Connector Type:UHF Coaxial; Body Style:Straight Plug; Coaxial Termination:Solder; Coaxial Cable Types:RG59, RG62, RG140, RG210; Contact Material:Brass; Contact Plating:Silver ;RoHS Compliant: Yes |
| 8375-1032-A-0 | 制造商:RAF Electronic Hardware 功能描述: |
| 83751-3 | 制造商:TE CONNECTIVITY 功能描述:WRENCH-LOK 350-350, 500-4 TE ENERGY |
發布緊急采購，3分鐘左右您將得到回復。