- 您現在的位置：買賣IC網 > PDF目錄2027 > 8375 (3M)SHEETS HARD LAM DISSP WHT 5X12' PDF資料下載
參數資料
| 型號： | 8375 |
| 廠商： | 3M |
| 文件頁數： | 12/16頁 |
| 文件大小： | 0K |
| 描述： | SHEETS HARD LAM DISSP WHT 5X12' |
| MSDS 材料安全數據表： | 8300 Series Hard Laminate MSDS |
| 標準包裝： | 5 |
| 系列： | 8300 |
| 墊子類型： | 桌子，工作臺卷筒 |
| 形狀： | 矩形 |
| 長度： | 12'（3.66m） |
| 寬： | 5'（1.52m） |
| 厚度： | 0.04"（1.02mm） |
| 顏色： | 白 |
| 材質： | Laminate |
| 特點： | 耗散 |
| 其它名稱： | 05400718636 98079816025 |
78-8136-3801-8
A.
Both the laminate and the substrate should be conditioned at approximately 75°F (24°C) and 4555%
RH for a minimum of 48 hours prior to fabrication.
B.
Provision should be made to allow air circulation around the various components of the fabrication
process (i.e., laminate, substrate, etc.).
C.
Where cracking may be a problem due to moisture differentials, the laminate should be thoroughly
dried out to minimize the rate of shrinkage. Fabricators have not experienced problems with buckling
or lifting of laminate when the laminate was dried prior to lamination and then later took on moisture.
(Note: Moisture in the laminate enhances its postforming properties.)
D.
Decreasing the ambient humidity minimizes stress cracking
Increasing the ambient humidity facilitates postforming
7.0
Fabrication
3M Rigid Worksurface 8300 Series is a rigid product and the top surface is very hard. Special tools and
procedures are required in order to fabricated this product successfully.
A.
Cutting/sawing/routing:
1. To avoid chipping during sawing, it is important that the rotation of the blade be such that the teeth of
the blade first contact and cut into the decorative (top) surface of the laminate. Therefore, with a hand
circular saw, the laminate should be cut with the decorative surface face down. With a table saw, the
decorative surface should face up.
2. Blades and bits used should be carbidetipped. A blade with more teeth will make a smoother cut.
Blades/bits should always be sharp. Recommended saw blades: triple chip grind, 10 – 15 degrees
positive rake. Ten inch diameter minimum 80 teeth, twelve inch diameter minimum 100 teeth.
3. The higher the rotation speed of the blade or bit, the cleaner the cut will be.
Caution: Do not exceed manufacturers recommended rotation speeds.
4. The laminate should not be forced into a cutting blade, and it must be supported near the blade,
especially when cutting unmounted laminate.
5. When cutting openings into a finished benchtop covered with laminate, never cut the inside corners
of the opening at 90° (the point at which each such cut ends can serve as a source for a crack.)
Always round such inside corners to a minimum radius to 0.125 in. (3.2 mm). However, the largest
possible radius should be used.
6. After cutting/sawing/routing, the edges of the laminate should always be filed or sanded to remove
chips or nicks that may lead to a crack later on.
B.
Sanding:
Sanding and filing should always be directed parallel to or away from the decorative surface.
C.
Drilling:
Recommendations are generally the same as those for sawing. In addition, the material being drilled
should be backed to prevent breakout at the bottom of the hole.
8.0
Postforming
A.
The minimum radius around which 3M Rigid Worksurface 8300 should be formed is 0.50 in. when
parallel to the machine direction. If the laminate is postformed perpendicular to the machine direction
the minimum radius is 0.625 in.
B.
Laminate sheets can be formed only in a straight line. They cannot be drawn over curved edges (e.g.,
covering a round tabletop) like vacuumformable plastic sheets can. The substrate must be clean,
smooth, and straight. Parallelism is essential in the moving parts of the forming operation.
C.
In general, the laminate should be only slightly larger than the substrate [0.1250.25 in. (3.26.4 mm)]
and should be trimmed after the forming operation is completed. Excessive overhang will tend to crack
or buckle during the postforming process. Check the edges of the laminate prior to forming. Any nicks
or cracks should be filed smooth before forming; if not, cracks can develop at these rough spots.
相關PDF資料 |
PDF描述 |
|---|---|
| 8812 | TABLE MAT GREEN |
| 91070 | WRIST STRAP SPEIDEL 6'ANGLE 4MM |
| 91095 | CORD GROUND WS COILED 6' RT ANG |
| 9500 | FLOOR RUNNER ANTI-FATIGUE 3'X 5' |
| 960X/980X | WALL TRANSFORMER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 8375 5X12 | 功能描述:TABLE LAMINATE WHITE 5'X1' 制造商:scs 系列:- 零件狀態:有效 墊類型:桌子，工作臺 形狀:矩形 長度:5'（1.52m） 寬度:1'（0.30m） 厚度:0.039"（0.99mm） 顏色:白 材料:層壓 特性:- 包括:- 標準包裝:5 |
| 83-750 | 功能描述:RF 連接器 STRT PLG 59/62/9209 8241 8279 UG-111/U RoHS:否 制造商:Bomar Interconnect 產品:Connectors 射頻系列:BNC 型式:Jack (Female) 極性: 觸點電鍍:Gold 阻抗: 端接類型:Solder 主體類型:Straight Bulkhead 電纜類型: |
| 83-750 (UG-111/U) | 制造商:Amphenol RF 功能描述:RF/COAXIAL UHF PLUG STRAIGHT SOLDER 制造商:Amphenol RF 功能描述:RF/COAXIAL, UHF PLUG, STRAIGHT, SOLDER 制造商:Amphenol RF 功能描述:RF/COAXIAL, UHF PLUG, STRAIGHT, SOLDER; Series:-; Connector Type:UHF Coaxial; Body Style:Straight Plug; Coaxial Termination:Solder; Coaxial Cable Types:RG59, RG62, RG140, RG210; Contact Material:Brass; Contact Plating:Silver ;RoHS Compliant: Yes |
| 8375-1032-A-0 | 制造商:RAF Electronic Hardware 功能描述: |
| 83751-3 | 制造商:TE CONNECTIVITY 功能描述:WRENCH-LOK 350-350, 500-4 TE ENERGY |
發布緊急采購，3分鐘左右您將得到回復。