參數資料
型號: 78Q2120
廠商: Electronic Theatre Controls, Inc.
英文描述: 10/100BASE-TX Ethernet Transceiver
中文描述: 10/100BASE-TX以太網收發器
文件頁數: 5/33頁
文件大?。?/td> 200K
代理商: 78Q2120
78Q2120
10/100BASE-TX
Ethernet Transceiver
MDIO pin at the rising edge of the MDC clock signal.
Once
the
preamble
is
management control logic looks for the start-of-
frame sequence and a read or write op-code,
followed by the PHYAD and REGAD fields. For a
read operation, the MDIO port becomes enabled as
an output and the register data is loaded into a shift
register for transmission. The 78Q2120 can work
with a one bit preamble rather than the 32 bits
proscribed by IEEE-802.3. This allows for faster
programming of the registers. If a register does not
exist at an address indicated by the REGAD field or
5
received,
the
station
if the PHYAD field does not match the 78Q2120
PHYAD indicated by the PHYAD pins, a read of the
MDIO port will return all ones. For a write operation,
the data is shifted in and loaded into the appropriate
register after the sixteenth data bit has been
received. Writes to registers not supported by the
78Q2120 are ignored.
When the PHYAD field is all zeros, the Station
Management Entity (STA) is requesting a broadcast
data transaction. All PHYs sharing the same
Management
Interface
broadcast request. All 78Q2120 will respond to the
broadcast data transaction.
must
respond
to
this
ADDITIONAL FEATURES
LED INDICATORS
There are seven LED pins that can be used to
indicate various states of operation of the 78Q2120.
There is an LED pin that indicates the link is up
(
LEDL
), others that indicate the 78Q2120 is either
transmitting (
LEDTX
) or receiving (
LEDRX
), one that
signals a collision event (
LEDCOL
), two more that
reflect the data rate (
LEDBTX
and
LEDBT
), and one
that
reflects
full
duplex
(
LEDFDX
).
mode
of
operation
GENERAL PURPOSE I/O INTERFACE
(80-TQFP ONLY)
The 78Q2120 80-pin TQFP has a two pin, bi-
directional, general purpose interface that can be
used for external control or to monitor external
signals. The direction of these pins and data that is
either driven or read from these pins is configured
via bits MR16.9:6 as detailed in the Vendor Specific
Register description of MR16.
INTERRUPT PIN
The 78Q2120 has an Interrupt pin (INTR) that is
asserted whenever any of the eight interrupt bits of
MR17.7:0 are set. These interrupt bits can be disabled
via MR17.15:8 Interrupt Enable bits. The active level
of the INTR pin is controlled by the Interrupt Level bit,
MR16.14. When the INTR pin is not asserted, the pin
is held in a high impedance state.
相關PDF資料
PDF描述
78Q2120-64 10/100BASE-TX Ethernet Transceiver
78Q2120-64CG 10/100BASE-TX Ethernet Transceiver
78Q2120-64CGT 10/100BASE-TX Ethernet Transceiver
78Q2120-64T 10/100BASE-TX Ethernet Transceiver
78Q2120-CGT 10/100BASE-TX Ethernet Transceiver
相關代理商/技術參數
參數描述
78Q2120-64 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10/100BASE-TX Ethernet Transceiver
78Q2120-64CG 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10/100BASE-TX Ethernet Transceiver
78Q2120-64CGT 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10/100BASE-TX Ethernet Transceiver
78Q2120-64T 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10/100BASE-TX Ethernet Transceiver
78Q2120C 制造商:TDK 制造商全稱:TDK Electronics 功能描述:10/100BASE - TX Transceiver