- 您現在的位置：買賣IC網 > PDF目錄369351 > 78Q2120 (Electronic Theatre Controls, Inc.) 10/100BASE-TX Ethernet Transceiver PDF資料下載
參數資料
| 型號： | 78Q2120 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 10/100BASE-TX Ethernet Transceiver |
| 中文描述： | 10/100BASE-TX以太網收發(fā)器 |
| 文件頁數： | 4/33頁 |
| 文件大?。?/td> | 200K |
| 代理商： | 78Q2120 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
78Q2120
10/100BASE-TX
Ethernet Transceiver
SQE TEST
The 78Q2120 supports the signal quality error
(SQE) function detailed in IEEE-802.3. At an
interval of 1
μ
s after each negative transition of the
TXEN pin in 10BASE-T mode, the COL pin will go
high for a period of 1
μ
s. This function can be
disabled through register bit MR16.11.
4
NATURAL LOOPBACK
When the 78Q2120 is transmitting and not receiving
on the twisted pair media, data on the TXD pins is
looped back onto the RXD pins. During a collision,
data from the RXI pins is routed to the RXD pins.
The natural loopback function can be enabled
through register bit MR16.10.
REPEATER MODE
When the RPTR pin is high or register bit MR 16.15
is set the 78Q2120 is placed in repeater mode. In
this mode, full duplex operation is prohibited, CRS
responds only to receive activity and, in 10BASE-T
mode, the SQE test function is disabled.
AUTO-NEGOTIATION
The
78Q2120
functions of Clause 28 of IEEE-802.3. This function
can be enabled via a pin strap to the device or
through registers. If the ANEGA pin is tied high, the
auto-negotiation function defaults to on and bit
MR0.12, ANEGEN, is high after reset. Software can
disable the auto-negotiation function by writing to bit
MR0.12 If the ANEGA pin is tied low the function
defaults to off and bit MR0.12 is set low after reset
and cannot be written to.
supports
the
auto-negotiation
The contents of register MR4 are sent to the
78Q2120’s link partner during auto-negotiation,
coded in fast link pulses. Bits MR4.8:5 reflect the
state of the TECH[2:0] pins after reset. If TECH[2:0]
= 111, then all 4 bits are high. If TECH[2:0] = 001,
then only bit 5 is high. After reset, software can
change any of these bits from a 1 to a 0; but not
from a 0 to a 1. Therefore, a technology permitted by
the setting of the TECH pins can be disabled, but
one not permitted cannot be enabled.
With auto-negotiation enabled, the 78Q2120 will
start sending fast link pulses at power on, loss of link
or a command to restart. At the same time it will
look for either 10BASE-T idle, 100BASE-TX idle or
fast link pulses from its link partner. If either idle
pattern is detected, the 78Q2120 configures itself in
half-duplex mode at the appropriate speed. If it
detects fast link pulses, it decodes and analyzes the
link code transmitted by the link partner. When
three identical link code words are received (ignoring
the acknowledge bit) the link code word is stored in
register 5. Upon receiving three more identical link
code words, with the acknowledge bit set, the
78Q2120 configures itself to the highest priority
technology common to the two link partners. The
technology priorities are, in descending order:
100BASE-TX, Full Duplex
100BASE-TX, Half Duplex
10BASE-T, Full Duplex
10BASE-T, Half Duplex
Once auto-negotiation is complete, register bits
MR18.11:10 will reflect the actual speed and duplex
that was chosen.
If auto-negotiation fails to establish a link for any
reason, register bit MR18.12 will reflect this and auto
negotiation will restart from the beginning. Writing a
one to bit MR0.9, RANEG, will also cause auto-
negotiation to restart.
MEDIA INDEPENDENT INTERFACE
MII Transmit and Receive Operation
The
independent transmit and receive paths for both
10Mb/s and 100Mb/s data rates as described in
Clause 22 of the IEEE-802.3 standard.
The transmit clock, TX_CLK, provides the timing
reference for the transfer of TX_EN, TXD[3:0], and
TX_ER signals from the MAC to the 78Q2120.
TXD[3:0] is captured on the rising edge of TX_CLK
when TX_EN is asserted. TX_ER is also captured
on the rising edge of TX_CLK and is asserted by the
MAC to request that an error code group be
transmitted. The assertion of TX_ER has no affect
when the 78Q2120 is operating in 10BASE-T mode.
The receive clock, RX_CLK, provides the timing
reference to transfer RX_DV, RXD[3:0], and RX_ER
signals from the 78Q2120 to the MAC. RX_DV
transitions synchronously with respect to RX_CLK and
is asserted when the 78Q2120 is presenting valid data
on RXD[3:0]. RX_ER is asserted when a code group
violation has been detected in the current receive
packet and is also synchronous to RX_CLK.
MII
interface
on
the
78Q2120
provides
STATION MANAGEMENT INTERFACE
The station management interface consists of
circuitry which implements the serial protocol as
described in Clause 22.2.4.4 of IEEE-802.3. A 16-bit
shift register receives serial data applied to the
相關PDF資料 |
PDF描述 |
|---|---|
| 78Q2120-64 | 10/100BASE-TX Ethernet Transceiver |
| 78Q2120-64CG | 10/100BASE-TX Ethernet Transceiver |
| 78Q2120-64CGT | 10/100BASE-TX Ethernet Transceiver |
| 78Q2120-64T | 10/100BASE-TX Ethernet Transceiver |
| 78Q2120-CGT | 10/100BASE-TX Ethernet Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 78Q2120-64 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10/100BASE-TX Ethernet Transceiver |
| 78Q2120-64CG | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10/100BASE-TX Ethernet Transceiver |
| 78Q2120-64CGT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10/100BASE-TX Ethernet Transceiver |
| 78Q2120-64T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10/100BASE-TX Ethernet Transceiver |
| 78Q2120C | 制造商:TDK 制造商全稱:TDK Electronics 功能描述:10/100BASE - TX Transceiver |
發(fā)布緊急采購，3分鐘左右您將得到回復。