- 您現在的位置：買賣IC網 > PDF目錄68811 > 71M6534-IGTR/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP120 PDF資料下載
參數資料
| 型號： | 71M6534-IGTR/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP120 |
| 封裝： | LEAD FREE, LQFP-120 |
| 文件頁數： | 60/124頁 |
| 文件大?。?/td> | 2008K |
| 代理商： | 71M6534-IGTR/F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁當前第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁
71M6533/71M6534 Data Sheet
FDS_6533_6534_004
40
2007-2009 TERIDIAN Semiconductor Corporation
v1.1
FLSH_PWE (flash program write enable) differentiates 80515 data store instructions (MOVX@DPTR,A)
between Flash and XRAM writes. This bit must be cleared by the MPU after each byte write operation.
Write operations to this bit are inhibited when interrupts are enabled.
The MPU cannot write to flash while the CE is executing its code from flash. Two interrupts warn of colli-
sions between the MPU firmware and the CE timing. If a flash write operation is attempted while the CE
is busy, the flash write will not execute and the FW_COL0 interrupt will be issued. If a flash write is still in
progress when the CE would otherwise begin a code pass, the code pass is skipped, the write operation
is completed, and the FW_COL1 interrupt is issued.
The simplest flash write procedure disables the CE during the write operation and interpolates the meter-
ing measurements. However, this results in the loss of at least one second of data, because the CE has
to resynchronize with the mains voltage.
There is a brief guaranteed interval (typically 1/32768 s) between CE executions which occurs 2520 times
per second. The start of the interval can be detected with the CE_BUSY interrupt which occurs on the
falling edge of CE_BUSY (an internal signal measurable from TMUXOUT). However, this guaranteed idle
time (30.5 s) is too short to write a byte which takes 42 s or to erase a page of flash memory which
takes at least 20 ms. Some CE code has substantially longer idle times, but in those cases, firmware in-
terrupt latencies can easily consume the available write time. If a flash write fails in this scheme, the fail-
ure can be detected with the FWCOL0 or FWCOL1 interrupt and the write can be retried.
It is practical to pre-erase pages, disable interrupts and poll the CE_BUSY interrupt flag, IRCON[2]. This
method avoids problems with interrupt latency, but can still result in a write failure if the CE code takes
too much time. As mentioned above, polling FWCOL0 and FWCOL1 can detect write failures. However,
the speed in a polling write is only 2520 bytes per second and the firmware cannot respond to interrupts.
As an alternative to using flash, a small EEPROM can store data without compromises. EEPROM inter-
faces are included in the device.
Updating Individual Bytes in Flash Memory
The original state of a flash byte is 0xFF (all ones). Once a value other than 0xFF is written to a flash
memory cell, overwriting with a different value usually requires that the cell be erased first. Since cells
cannot be erased individually, the page has to be copied to RAM, followed by a page erase. After this,
the page can be updated in RAM and then written back to the flash memory.
Flash Erase Procedures
Flash erasure is initiated by writing a specific data pattern to specific SFR registers in the proper sequence.
These special pattern/sequence requirements prevent inadvertent erasure of the flash memory.
The mass erase sequence is:
1.
Write 1 to the FLSH_MEEN bit (SFR address 0xB2[1].
2.
Write the pattern 0xAA to FLSH_ERASE (SFR address 0x94).
The mass erase cycle can only be initiated when the ICE port is enabled.
The page erase sequence is:
1.
Write the page address to FLSH_PGADR (SFR address 0xB7[7:2].
2.
Write the pattern 0x55 to FLSH_ERASE (SFR address 0x94).
Bank-Switching
The program memory of the 71M6533/71M6534 consists of a fixed lower bank of 32 KB, addressable at
0x0000 to 0x7FFF plus an upper banked area of 32 KB, addressable at 0x8000 to 0xFFFF. The I/O RAM
register FL_BANKis used to switch one of four (71M6533/H, 71M6534) or eight (71M6534H) memory banks
of 32 KB each into the address range from 0x8000 to 0xFFFF. Note that when FL_BANK = 0, the upper
bank is the same as the lower bank. Table 38 illustrates the bank switching mechanism.
相關PDF資料 |
PDF描述 |
|---|---|
| 71M6533H-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6533H-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6533-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6534H-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP120 |
| 71M6533-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 71M6541D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:71M6541D/71M6541F/71M6541G/71M6542F/71M6542G 是 TeridianTM 的第4 代高集成度單相電表SoC |
| 71M6541D_1111 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Energy Meter ICs |
| 71M6541D-IGT/F | 功能描述:計量片上系統 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6541D-IGTR/F | 功能描述:計量片上系統 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6541DT-IGT/F | 制造商:Maxim Integrated Products 功能描述:ENERGY METER ICS - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。