參數資料
型號: 71M6534-IGT/F
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: 模擬信號調理
英文描述: SPECIALTY ANALOG CIRCUIT, PQFP120
封裝: LEAD FREE, LQFP-120
文件頁數: 67/124頁
文件大?。?/td> 2008K
代理商: 71M6534-IGT/F
FDS_6533_6534_004
71M6533/71M6534 Data Sheet
v1.1
2007-2009 TERIDIAN Semiconductor Corporation
47
Table 41: EECTRL Bits for 2-pin Interface
Status
Bit
Name
Read/
Write
Reset
State
Polarity
Description
7
ERROR
R
0
Positive
1 when an illegal command is received.
6
BUSY
R
0
Positive
1 when serial data bus is busy.
5
RX_ACK
R
1
Negative
0 indicates that the EEPROM sent an ACK bit.
4
TX_ACK
R
1
Negative
0 indicates when an ACK bit has been sent to the
EEPROM.
3:0
CMD[3:0]
W
0000
Positive
CMD[3:0]
Operation
0000
No-op command. Stops the I
2C clock
(SCK, DIO4). If not issued, SCK
keeps toggling.
0010
Receive a byte from the EEPROM
and send ACK.
0011
Transmit a byte to the EEPROM.
0101
Issue a STOP sequence.
0110
Receive the last byte from the
EEPROM and do not send ACK.
1001
Issue a START sequence.
Others
No operation, set the ERROR bit.
The EEPROM interface can also be operated by controlling the DIO4 and DIO5 pins directly. In
this case, a resistor has to be used in series with SDA to avoid data collisions due to limits in the
speed at which the SDA pin can be switched from output to input. However, controlling DIO4 and
DIO5 directly is discouraged, because it may tie up the MPU to the point where it may become too
busy to process interrupts.
Three-wire (-Wire) EEPROM Interface
A 500 kHz three-wire interface, using SDATA, SCK, and a DIO pin for CS is available. The interface is
selected by setting DIO_EEX = 3. The EECTRL bits when the three-wire interface is selected are shown in
Table 42. When EECTRL is written, up to 8 bits from EEDATA are either written to the EEPROM or read
from the EEPROM, depending on the values of the EECTRL bits.
The -Wire EEPROM interface is only functional when MPU_DIV[2:0] = 000.
Table 42: EECTRL Bits for the 3-wire Interface
Control
Bit
Name
Read/
Write
Description
7
WFR
W
Wait for Ready. If this bit is set, the trailing edge of BUSY will be delayed
until a rising edge is seen on the data line. This bit can be used during
the last byte of a Write command to cause the INT5 interrupt to occur
when the EEPROM has finished its internal write sequence. This bit is
ignored if HiZ=0.
6
BUSY
R
Asserted while the serial data bus is busy. When the BUSY bit falls, an
INT5 interrupt occurs.
5
HiZ
W
Indicates that the SD signal is to be floated to high impedance immedi-
ately after the last SCK rising edge.
4
RD
W
Indicates that EEDATA is to be filled with data from EEPROM.
相關PDF資料
PDF描述
71M6533-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6534H-IGT/F SPECIALTY ANALOG CIRCUIT, PQFP120
71M6533H-IGT/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6533-IGT/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6542F-IGT/F SPECIALTY ANALOG CIRCUIT, PQFP100
相關代理商/技術參數
參數描述
71M6534-IGTR/F 功能描述:計量片上系統 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel
71M6541D 制造商:未知廠家 制造商全稱:未知廠家 功能描述:71M6541D/71M6541F/71M6541G/71M6542F/71M6542G 是 TeridianTM 的第4 代高集成度單相電表SoC
71M6541D_1111 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Energy Meter ICs
71M6541D-IGT/F 功能描述:計量片上系統 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel
71M6541D-IGTR/F 功能描述:計量片上系統 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel