- 您現在的位置：買賣IC網 > PDF目錄359884 > 4250 Low-Cost, 2.7V to 5.5V Temperature Switches in a SOT23 PDF資料下載
參數資料
| 型號： | 4250 |
| 英文描述： | Low-Cost, 2.7V to 5.5V Temperature Switches in a SOT23 |
| 中文描述： | 4250組數據表數據表652K/NOV.30.97 |
| 文件頁數： | 20/59頁 |
| 文件大?。?/td> | 652K |
| 代理商： | 4250 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
19
MITSUBISHI MICROCOMPUTERS
4250 Group
SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
K0
3
K0
2
K0
1
K0
0
Instruction clock divided by 4
Instruction clock divided by 512
Rising waveform (“L”
→
“H”)
Falling waveform (“H”
→
“L”)
Key-on wakeup not used
Key-on wakeup used (“L” level recognized)
Key-on wakeup not used
Key-on wakeup used (“L” level recognized)
Prescaler dividing ratio selection bit
Interrupt valid waveform for INT pin/
key-on wakeup valid waveform selection
bit (Note 2)
Ports G
1
–G
3
key-on wakeup control bit
Ports S
0
–S
3
key-on wakeup control bit
Key-on wakeup control register K0
at reset : 0000
2
at RAM back-up : state retained
0
1
0
1
0
1
0
1
R/W
Notes 1: “R” represents read enabled, and “W” represents write enabled.
2: Set a value to the bit 2 of register K0, and execute the SNZ0 instruction to clear the EXF0 flag to “0” after executing at least
one instruction. According to the input state of G
0
/INT pin, the external interrupt request flag (EXF0) may be set to “1” when
the interrupt valid waveform is changed.
(1) External interrupt request flag (EXF0)
External interrupt request flag (EXF0) is set to “1” when a valid
waveform is input to G
0
/INT pin.
The valid waveforms causing the interrupt must be retained
at their level for 5 cycles or more of f(X
IN
) (Refer to Figure
16).
The state of EXF0 flag can be examined with the skip
instruction (SNZ0). Use the timer control register V1 to select
the interrupt or the skip instruction. The EXF0 flag is cleared
to “0” when an interrupt occurs or when the next instruction is
skipped with the skip instruction.
External interrupt activated condition
External interrupt activated condition is satisfied when a
valid waveform is input to G
0
/INT pin.
The valid waveform can be selected from rising waveform
or falling waveform. An example of how to use the external
interrupt is as follows.
Select the valid waveform with the bit 2 of register K0.
Clear the EXF0 flag to “0” with the SNZ0 instruction.
Set the NOP instruction for the case when a skip is
performed with the SNZ0 instruction.
Set both the external interrupt enable bit (V1
0
) and the INTE
flag to “1.”
The external interrupt is now enabled. Now when a valid
waveform is input to the G
0
/INT pin, the EXF0 flag is set to “1”
and the external interrupt occurs.
(2) Control register related to external interrupt
Key-on wakeup control register K0
Register K0 controls the valid waveform for the external
interrupt and key-on wakeup function. Set the contents of
this register through register A with the TK0A instruction.
The TAK0 instruction can be used to transfer the contents
of register K0 to register A.
Table 8 Control register related to external interrupt
相關PDF資料 |
PDF描述 |
|---|---|
| 4251 | ATEMSCHUTZ MASKE WARTUNGSFREI |
| 425 | SURFACE MOUNT FUSES |
| 4263 | Low-Cost, 2.7V to 5.5V Temperature Switches in a SOT23 |
| 23012 | PATCH LEAD EXT UTP 1M |
| 23132 | CPU Peripheral Monitor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 42500 | 功能描述:環境檢測設備 THERMOMETER POCKET RoHS:否 制造商:Fluke 設備類型:Vibration Meter 測量儀器:Vibration |
| 4250-0000LCMD | 制造商:3M Electronic Products Division 功能描述: |
| 4250-0000NCMD | 制造商:3M Electronic Products Division 功能描述: |
| 425-00001-901 | 制造商:Volex Group 功能描述: |
| 425-00001-904 | 制造商:Volex Group 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。