參數資料
型號： 25AA512
廠商： Microchip Technology Inc.
英文描述： 512 Kbit SPI Bus Serial EEPROM
中文描述： 512千位SPI總線串行EEPROM
文件頁數： 8/32頁
文件大?。?/td> 485K
代理商： 25AA512
25AA512/25LC512
DS22021B-page 8
Preliminary
2007 Microchip Technology Inc.
2.2
Write Sequence
Prior to any attempt to write data to the 25XX512, the
write enable latch must be set by issuing the
WREN
instruction (Figure 2-4). This is done by setting CS low
and then clocking out the proper instruction into the
25XX512. After all eight bits of the instruction are trans-
mitted, the CS must be brought high to set the write
enable latch. If the write operation is initiated immedi-
ately after the
WREN
instruction without CS being
brought high, the data will not be written to the array
because the write enable latch will not have been
properly set.
A write sequence includes an automatic, self timed
erase cycle. It is not required to erase any portion of the
memory prior to issuing a
WRITE
instruction.
Once the write enable latch is set, the user may
proceed by setting the CS low, issuing a
WRITE
instruc-
tion, followed by the 16-bit address, and then the data
to be written. Up to 128 bytes of data can be sent to the
device before a write cycle is necessary. The only
restriction is that all of the bytes must reside in the
same page. When doing a write of less than 128 bytes
the data in the rest of the page is refreshed along with
the data bytes being written. This will force the entire
page to endure a write cycle, for this reason endurance
is specified per page
.
For the data to be actually written to the array, the CS
must be brought high after the Least Significant bit (D0)
of the
n
th
data byte has been clocked in. If CS is
brought high at any other time, the write operation will
not be completed. Refer to Figure 2-2 and Figure 2-3
for more detailed illustrations on the byte write
sequence and the page write sequence, respectively.
While the write is in progress, the STATUS register may
be read to check the status of the WPEN, WIP, WEL,
BP1 and BP0 bits (Figure 2-6). A read attempt of a
memory array location will not be possible during a
write cycle. When the write cycle is completed, the
write enable latch is reset.
FIGURE 2-2:
BYTE WRITE SEQUENCE
Note:
Page write operations are limited to writing
bytes within a single physical page,
regardless
of the number of bytes
actually being written. Physical page
boundaries start at addresses that are
integer multiples of the page buffer size (or
‘page size’), and end at addresses that are
integer multiples of page size – 1. If a
Page Write command attempts to write
across a physical page boundary, the
result is that the data wraps around to the
beginning of the current page (overwriting
data previously stored there), instead of
being written to the next page as might be
expected. It is therefore necessary for the
application software to prevent page write
operations that would attempt to cross a
page boundary.
SO
SI
CS
9 10 11
21 22 23 24 25 26 27 28 29 30 31
0
0
0
0
0
0
0
1
15 14 13 12
2
1
0
7
6
5
4
3
2
1
0
Instruction
16-bit Address
Data Byte
High-Impedance
SCK
0
2
3
4
5
6
7
1
8
Twc
相關PDF資料
PDF描述
25AMB12026MB SINGLE PHASE BRIDGE
25AMB12036MB SINGLE PHASE BRIDGE
25A SCHOTTKY RECTIFIER
25C128 128K 5.0V SPI Bus Serial EEPROM(4.5~5.5V,128K位,SPI總線串行EEPROM)
25LC128 128K 5.0V SPI Bus Serial EEPROM(2.5~5.5V,128K位,SPI總線串行EEPROM)
相關代理商/技術參數
參數描述
25AA512_10 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:512 Kbit SPI Bus Serial EEPROM
25AA512-1/MF 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:512 Kbit SPI Bus Serial EEPROM
25AA512-1/P 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:512 Kbit SPI Bus Serial EEPROM
25AA512-1/SN 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:512 Kbit SPI Bus Serial EEPROM
25AA512-E/MF 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:512 Kbit SPI Bus Serial EEPROM
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*