參數資料
型號: 24WC32
元件分類: EEPROM
英文描述: 64K 8K x 8 Battery-Voltage CMOS E2PROM
中文描述: 64K的8K的× 8電池電壓的CMOS E2PROM的
文件頁數: 5/8頁
文件大?。?/td> 74K
代理商: 24WC32
Preliminary
CAT24WC32/64
5
Doc. No. 25053-00 2/98 S-1
I
2
C BUS PROTOCOL
The features of the I
2
C bus protocol are defined as
follows:
(1) Data transfer may be initiated only when the bus is
not busy.
(2) During a data transfer, the data line must remain
stable whenever the clock line is high. Any changes
in the data line while the clock line is high will be
interpreted as a START or STOP condition.
START Condition
The START Condition precedes all commands to the
device, and is defined as a HIGH to LOW transition of
SDA when SCL is HIGH. The CAT24WC32/64 monitors
the SDA and SCL lines and will not respond until this
condition is met.
STOP Condition
A LOW to HIGH transition of SDA when SCL is HIGH
determines the STOP condition. All operations must end
with a STOP condition.
DEVICE ADDRESSING
The bus Master begins a transmission by sending a
START condition. The Master sends the address of the
particular slave device it is requesting. The four most
significant bits of the 8-bit slave address are fixed as
1010 (Fig. 5). The next three bits (A2, A1, A0) are the
device address bits; up to eight 32K/64K devices may
to be connected to the same bus. These bits must
Figure 4. Acknowledge Timing
5027 FHD F07
Figure 5. Slave Address Bits
5020 FHD F06
ACKNOWLEDGE
1
START
SCL FROM
MASTER
8
9
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
1
0
1
0
A2
A1
A0
R/W
compare to the hardwired input pins, A2, A1 and A0. The
last bit of the slave address specifies whether a Read or
Write operation is to be performed. When this bit is set
to 1, a Read operation is selected, and when set to 0, a
Write operation is selected.
After the Master sends a START condition and the slave
address byte, the CAT24WC32/64 monitors the bus and
responds with an acknowledge (on the SDA line) when
its address matches the transmitted slave address. The
CAT24WC32/64 then performs a Read or Write opera-
tion depending on the state of the R/W bit.
Acknowledge
After a successful data transfer, each receiving device is
required to generate an acknowledge. The Acknowledg-
ing device pulls down the SDA line during the ninth clock
cycle, signaling that it received the 8 bits of data.
The CAT24WC32/64 responds with an acknowledge
after receiving a START condition and its slave address.
If the device has been selected along with a write
operation, it responds with an acknowledge after receiv-
ing each 8-bit byte.
When the CAT24WC32/64 begins a READ mode it
transmits 8 bits of data, releases the SDA line, and
monitors the line for an acknowledge. Once it receives
this acknowledge, the CAT24WC32/64 will continue to
transmit data. If no acknowledge is sent by the Master,
the device terminates data transmission and waits for a
STOP condition. The master must then issue a stop
condition to return the CAT24WC32/64 to the standby
power mode and place the device in a known state.
相關PDF資料
PDF描述
250-8501-010 Low-Power, SPST, Fast, CMOS Analog Switch
2500-10J Molded Unshielded RF Coils
2500-00J Molded Unshielded RF Coils
2500-02J Molded Unshielded RF Coils
2500-04J Molded Unshielded RF Coils
相關代理商/技術參數
參數描述
24WC32P 制造商:CATALYST 功能描述:
24WR10KLFTR 制造商:BITECH 制造商全稱:Bi technologies 功能描述:4mm Diameter Single Turn Cermet Trimming Potentiometer
24X 功能描述:燈 24V .035A RoHS:否 制造商:Chicago Miniature 燈類型:Incandescent 燈座類型:Wire Terminal 燈大小:T-1 3/4 顏色: 電壓:14 V 工作電流: MSCP:0.3 MSCP 壽命:40000 hr 封裝:Bulk
24X 制造商:Pro-Signal 功能描述:Incandescent Lamp
24X10X0.2 2534P 制造商:Farnell / Pro-Power 功能描述:WIRE BRAID COPPER TINNED 63A 25M 制造商:pro-power 功能描述:WIRE BRAID, COPPER TINNED, 63A, 25M 制造商:pro-power 功能描述:SLEEVING, FLAT WIRE BRAID, 10MM W, TIN, 82FT; Sleeving / Tubing Type:Braided; Length:25m; Sleeving Material:Tinned Copper; Sleeving Color:Tin; Accessory Type:Braid; For Use With:Earth Bonding Straps ;RoHS Compliant: Yes