- 您現在的位置：買賣IC網 > PDF目錄371399 > 24LCS41A (Microchip Technology Inc.) 1K/4K 2.5V Dual Mode, Dual Port IIC Serial EEPROM(1K/4K位,2.5V雙模式,雙端口IIC串行EEPROM) PDF資料下載
參數資料
| 型號： | 24LCS41A |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 1K/4K 2.5V Dual Mode, Dual Port IIC Serial EEPROM(1K/4K位,2.5V雙模式,雙端口IIC串行EEPROM) |
| 中文描述： | 1K/4K 2.5V的雙模式，雙端口串行EEPROM國際進口證（1K/4K位，2.5V的雙模式，雙端口串行EEPROM的國際進口許可證） |
| 文件頁數： | 13/16頁 |
| 文件大?。?/td> | 104K |
| 代理商： | 24LCS41A |
1996 Microchip Technology Inc.
Preliminary
DS21175A-page 13
24LCS41A
8.0
PIN DESCRIPTIONS
8.1
DSDA
This pin is used to transfer addresses and data into and
out of the DDC Monitor Port, when the device is in the
Bi-directional Mode. In the Transmit-Only Mode, which
only allows data to be read from the device, data is also
transferred on the DSDA pin. This pin is an open drain
terminal, therefore the DSDA bus requires a pullup
resistor to V
CC
(typical 10K
for 100 kHz, 1K
for 400
kHz).
For normal data transfer in the Bi-directional Mode,
DSDA is allowed to change only during DSCL or MSDA
low. Changes during DSCL high are reserved for indi-
cating the START and STOP conditions.
8.2
DSCL
This pin is the clock input for the DDC Monitor Port
while in the Bi-directional Mode, and is used to synchro-
nize data transfer to and from the device. It is also used
as the signaling input to switch the device from the
Transmit-Only Mode to the Bi-directional Mode. It must
remain high for the chip to continue operation in the
Transmit-Only Mode.
8.3
VCLK
This pin is the clock input for the DDC Monitor Port
while in the Transmit-Only Mode. In the Transmit-Only
Mode, each bit is clocked out on the rising edge of this
signal. In the Bi-directional Mode, a high logic level is
required on this pin to enable write capability.
8.4
DWP
This pin is used for flexible write protection of the DDC
Monitor Port. When the last memory location (7Fh) is
written with any data, this pin is enabled and deter-
mines the write capability of the DDC port.
The DWP pin has an internal pull up resistor which will
allow write capability (assuming VCLK = 1) at all times
if this pin is floated.
8.5
MSCL
This pin is the clock input for the Microcontroller Access
Port, and is used to synchronize data transfer to and
from the device.
8.6
MSDA
This pin is used to transfer addresses and data into and
out of the Microcontroller Access Port. This pin is an
open drain terminal, therefore the MSDA bus requires a
pullup resistor to V
CC
(typical 10K
for 100 kHz, 1K
for 400 kHz).
MSDA is allowed to change only during MSCL low.
Changes during MSCL high are reserved for indicating
the START and STOP conditions.
相關PDF資料 |
PDF描述 |
|---|---|
| 24LCS41 | 1K/4K 2.5V Dual Mode, Dual Port IIC Serial EEPROM(1K/4K位,2.5V雙模式,雙端口IIC串行EEPROM) |
| 24LCS52 | Connectors |
| 24LC52-IP | 2K 2.5V I 2 C Serial EEPROM with Software Write Protect |
| 24LC52-ISN | 2K 2.5V I 2 C Serial EEPROM with Software Write Protect |
| 24LC52-IST | 2K 2.5V I 2 C Serial EEPROM with Software Write Protect |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 24LCS52/P | 功能描述:電可擦除可編程只讀存儲器 256x8 - 2.5V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| 24LCS52/SN | 功能描述:電可擦除可編程只讀存儲器 256x8 - 2.5V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| 24LCS52/ST | 功能描述:電可擦除可編程只讀存儲器 256x8 - 2.5V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| 24LCS52-I/MC | 功能描述:電可擦除可編程只讀存儲器 256x8 - 2.5V Industrial Temp RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| 24LCS52-I/MCG | 功能描述:電可擦除可編程只讀存儲器 256x8 - 2.5V Industrial Temp RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發(fā)布緊急采購，3分鐘左右您將得到回復。