- 您現在的位置：買賣IC網 > PDF目錄368730 > 16F84 (Microchip Technology Inc.) CAT 5E CROSSOVER, BLUE 15 FT PATCH CABLE PDF資料下載
參數資料
| 型號： | 16F84 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | CAT 5E CROSSOVER, BLUE 15 FT PATCH CABLE |
| 中文描述： | 18引腳閃存/ EEPROM的8位微控制器 |
| 文件頁數： | 52/124頁 |
| 文件大?。?/td> | 1322K |
| 代理商： | 16F84 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁當前第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁
PIC16F8X
DS30430C-page 52
1998 Microchip Technology Inc.
8.12.3
WAKE-UP USING INTERRUPTS
When global interrupts are disabled (GIE cleared) and
any interrupt source has both its interrupt enable bit
and interrupt flag bit set, one of the following will occur:
If the interrupt occurs
before
the execution of a
SLEEP
instruction, the
SLEEP
instruction will com-
plete as a NOP. Therefore, the WDT and WDT
postscaler will not be cleared, the TO bit will not
be set and PD bits will not be cleared.
If the interrupt occurs
during or after
the execu-
tion of a
SLEEP
instruction, the device will immedi-
ately wake up from sleep. The
SLEEP
instruction
will be completely executed before the wake-up.
Therefore, the WDT and WDT postscaler will be
cleared, the TO bit will be set and the PD bit will
be cleared.
Even if the flag bits were checked before executing a
SLEEP
instruction, it may be possible for flag bits to
become set before the
SLEEP
instruction completes. To
determine whether a
SLEEP
instruction executed, test
the PD bit. If the PD bit is set, the
SLEEP
instruction was
executed as a NOP.
To ensure that the WDT is cleared, a
CLRWDT
instruc-
tion should be executed before a
SLEEP
instruction.
8.13
Program Verification/Code Protection
If the code protection bit(s) have not been
programmed, the on-chip program memory can be
read out for verification purposes.
8.14
ID Locations
Four memory locations (2000h - 2003h) are designated
as ID locations to store checksum or other code
identification numbers. These locations are not
accessible during normal execution but are readable
and writable only during program/verify. Only the
4 least significant bits of ID location are usable.
For ROM devices, these values are submitted along
with the ROM code.
8.15
In-Circuit Serial Programming
PIC16F8X
programmed while in the end application circuit. This is
simply done with two lines for clock and data, and three
other lines for power, ground, and the programming
voltage. Customers can manufacture boards with
unprogrammed devices, and then program the
microcontroller just before shipping the product,
allowing the most recent firmware or custom firmware
to be programmed.
The device is placed into a program/verify mode by
holding the RB6 and RB7 pins low, while raising the
MCLR pin from V
IL
to V
IHH
(see programming
specification). RB6 becomes the programming clock
and RB7 becomes the programming data. Both RB6
and RB7 are Schmitt Trigger inputs in this mode.
After reset, to place the device into programming/verify
mode, the program counter (PC) points to location 00h.
A 6-bit command is then supplied to the device, 14-bits
of program data is then supplied to or from the device,
using load or read-type instructions. For complete
details of serial programming, please refer to the
PIC16CXX Programming Specifications (Literature
#DS30189).
microcontrollers
can
be
serially
FIGURE 8-20: TYPICAL IN-SYSTEM SERIAL
PROGRAMMING
CONNECTION
For ROM devices, both the program memory and Data
EEPROM memory may be read, but only the Data
EEPROM memory may be programmed.
Note:
Microchip does not recommend code pro-
tecting widowed devices.
External
Connector
Signals
To Normal
Connections
To Normal
Connections
PIC16FXX
V
DD
V
SS
MCLR/V
PP
RB6
RB7
+5V
0V
V
PP
CLK
Data I/O
V
DD
相關PDF資料 |
PDF描述 |
|---|---|
| 16F84A | CAT 5E CROSSOVER PATCH CORD CABLE BLUE 20 FT |
| 16F871 | CAT 5E CROSSOVER PATCH CORD CABLE GREEN 6 FT |
| 16F872 | CAT 5E CROSSOVER PATCH CORD CABLE GREEN 10 FT |
| 16F876A | 28/40-pin Enhanced FLASH Microcontrollers |
| 16F876 | CAT 5E CROSSOVER, GREEN 15 FT PATCH CABLE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 16F84A | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:18-pin Enhanced Flash/EEPROM 8-Bit Microcontroller |
| 16F870 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:28/40-Pin 8-Bit CMOS FLASH Microcontrollers |
| 16F871 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:28/40-Pin 8-Bit CMOS FLASH Microcontrollers |
| 16F872 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:28-Pin, 8-Bit CMOS FLASH Microcontroller |
| 16F876 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:28/40-pin 8-Bit CMOS FLASH Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。