- 您現在的位置：買賣IC網 > PDF目錄16865 > 101-0433 (Rabbit Semiconductor)BOARD PROTOTYPING FOR RCM2100 PDF資料下載
參數資料
| 型號： | 101-0433 |
| 廠商： | Rabbit Semiconductor |
| 文件頁數： | 83/100頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD PROTOTYPING FOR RCM2100 |
| 標準包裝： | 1 |
| 附件類型： | 原型開發板 |
| 適用于相關產品： | RCM2100 |
| 其它名稱： | 101-433 101-433-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁當前第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁
User’s Manual
77
To maximize the availability of RCM2100 resources, the demonstration hardware (LEDs
and switches) on the Prototyping Board may be disconnected. This is done by cutting the
traces below the silk-screen outline of header JP1 on the bottom side of the Prototyping
Board. Figure B-4 shows the four places where cuts should be made. An exacto knife
would work nicely to cut the traces. Alternatively, a small standard screwdriver may be
carefully and forcefully used to wipe through the PCB traces.
Figure B-4. Where to Cut Traces to Permanently Disable
Demonstration Hardware on Prototyping Board
The power LED (PWR) and the RESET switch remain connected. Jumpers across the
appropriate pins on header JP1 can be used to reconnect specific demonstration hardware
later if needed.
Note that the pinout at location JP1 on the bottom side of the Prototyping Board (shown in
Figure B-4) is a mirror image of the top side pinout.
The Prototyping Board provides the user with RCM2100 connection points brought out con-
veniently to labeled points at headers J2 and J4 on the Prototyping Board. Small to medium
circuits can be prototyped using point-to-point wiring with 20 to 30 AWG wire between the
prototyping area and the holes at locations J2 and J4. The holes are spaced at 0.1" (2.5 mm),
Table B-2. Prototyping Board Jumper Settings
Header JP2
Pins
Description
1–2
PA0 to LED DS2
3–4
PA1 to LED DS3
5–6
PB2 to Switch S2
7–8
PB3 to Switch S3
S2
PB3
PB2
PA1
PA0
DS3
S3
DS2
Cut
JP1
Bottom Side
相關PDF資料 |
PDF描述 |
|---|---|
| 0982660965 | CBL 27PS 0.5MM JMPR TYPE A 1.18" |
| GEC19DRTN-S734 | CONN EDGECARD 38POS DIP .100 SLD |
| 0982660964 | CBL 27PS 0.5MM JMPR TYPE D 1.18" |
| SRR6038-820Y | INDUCTOR POWER 82UH .70A SMD |
| TCMD-22-T-12.00-01-N | CABLE ASSEM 2MM 44POS M-F 12" |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 101-0433-000 | 制造商:ITT Interconnect Solutions 功能描述:INSUL CA-KE18-4P RR / 101-0433-000 / Circular |
| 101-0434 | 功能描述:模塊化系統 - SOM RCM2100 RABBITCORE RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| 101-0434-000 | 制造商:ITT Interconnect Solutions 功能描述:INSUL CA-KE18-4S FR / 101-0434-000 / Circular |
| 101-0435 | 功能描述:模塊化系統 - SOM RCM2110 RABBITCORE RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| 101-0435-000 | 制造商:ITT Interconnect Solutions 功能描述:INSUL CA-KE18-4S RR / 101-0435-000 / Circular |
發布緊急采購，3分鐘左右您將得到回復。