- 您現在的位置：買賣IC網 > PDF目錄16865 > 101-0433 (Rabbit Semiconductor)BOARD PROTOTYPING FOR RCM2100 PDF資料下載
參數資料
| 型號： | 101-0433 |
| 廠商： | Rabbit Semiconductor |
| 文件頁數： | 33/100頁 |
| 文件大小： | 0K |
| 描述： | BOARD PROTOTYPING FOR RCM2100 |
| 標準包裝： | 1 |
| 附件類型： | 原型開發板 |
| 適用于相關產品： | RCM2100 |
| 其它名稱： | 101-433 101-433-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁
32
RabbitCore RCM2100
4.3 Serial Programming Cable
The programming cable is used to connect the RCM2100’s programming port to a PC
serial COM port. The programming cable converts the RS-232 voltage levels used by the
PC serial port to the TTL voltage levels used by the Rabbit 2000.
When the PROG connector on the programming cable is connected to the RCM2100’s
programming header, programs can be downloaded and debugged over the serial interface.
The DIAG connector of the programming cable may be used on the RCM2100’s program-
ming header with the RCM2100 operating in the Run Mode. This allows the programming
port to be used as a regular serial port.
4.3.1 Changing Between Program Mode and Run Mode
The RCM2100 is automatically in Program Mode when the PROG connector on the
programming cable is attached to the RCM2100, and is automatically in Run Mode when
no programming cable is attached. When the Rabbit 2000 is reset, the operating mode is
determined by the status of the SMODE pins. When the programming cable’s PROG
connector is attached, the SMODE pins are pulled high, placing the Rabbit 2000 in the
Program Mode. When the programming cable’s PROG connector is not attached, the
SMODE pins are pulled low, causing the Rabbit 2000 to operate in the Run Mode.
Figure 10. Switching Between Program Mode and Run Mode
A program “runs” in either mode, but can only be downloaded and debugged when the
RCM2100 module is in the Program Mode.
Refer to the Rabbit 2000 Microprocessor User’s Manual for more information on the pro-
gramming port and the programming cable.
RESET RabbitCore when changing mode:
Press RESET button (if using Prototyping Board), OR
Cycle power off/on
after removing or attaching programming cable.
To PC COM port
Run Mode
Program Mode
相關PDF資料 |
PDF描述 |
|---|---|
| 0982660965 | CBL 27PS 0.5MM JMPR TYPE A 1.18" |
| GEC19DRTN-S734 | CONN EDGECARD 38POS DIP .100 SLD |
| 0982660964 | CBL 27PS 0.5MM JMPR TYPE D 1.18" |
| SRR6038-820Y | INDUCTOR POWER 82UH .70A SMD |
| TCMD-22-T-12.00-01-N | CABLE ASSEM 2MM 44POS M-F 12" |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 101-0433-000 | 制造商:ITT Interconnect Solutions 功能描述:INSUL CA-KE18-4P RR / 101-0433-000 / Circular |
| 101-0434 | 功能描述:模塊化系統 - SOM RCM2100 RABBITCORE RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| 101-0434-000 | 制造商:ITT Interconnect Solutions 功能描述:INSUL CA-KE18-4S FR / 101-0434-000 / Circular |
| 101-0435 | 功能描述:模塊化系統 - SOM RCM2110 RABBITCORE RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| 101-0435-000 | 制造商:ITT Interconnect Solutions 功能描述:INSUL CA-KE18-4S RR / 101-0435-000 / Circular |
發布緊急采購，3分鐘左右您將得到回復。