doubl" />
參數資料
型號： 101-0433
廠商： Rabbit Semiconductor
文件頁數： 10/100頁
文件大?。?/td> 0K
描述： BOARD PROTOTYPING FOR RCM2100
標準包裝： 1
附件類型： 原型開發板
適用于相關產品： RCM2100
其它名稱： 101-433
101-433-ND
User’s Manual
11
2.2 Run a Sample Program
Once the RCM2100 is connected as described in the preceding pages, start Dynamic C by
double-clicking on the Dynamic C icon or by double-clicking on dcrab_XXXX.exe in
the Dynamic C root directory, where XXXX are version-specific characters. Dynamic C
uses the serial port specified during installation.
If you are using a USB port to connect your computer to the RCM2100 module, choose
Options > Project Options
and select “Use USB to Serial Converter” under the
Communications
tab.
Find the file PONG.C, which is in the Dynamic C SAMPLES folder. To run the program,
open it with the File menu (if it is not still open), then compile and run it by pressing F9 or
by selecting Run in the Run menu. The STDIO window will open and will display a small
square bouncing around in a box.
2.2.1 Troubleshooting
If Dynamic C appears to compile the BIOS successfully, but you then receive a communi-
cation error message when you compile and load the sample program, it is possible that
your PC cannot handle the higher program-loading baud rate. Try changing the maximum
download rate to a slower baud rate as follows.
Locate the Serial Options dialog in the Dynamic C Options > Project Options >
Communications
menu. Select a slower Max download baud rate.
If a program compiles and loads, but then loses target communication before you can
begin debugging, it is possible that your PC cannot handle the default debugging baud
rate. Try lowering the debugging baud rate as follows.
Locate the Serial Options dialog in the Dynamic C Options > Project Options >
Communications
menu. Choose a lower debug baud rate.
If there are any other problems:
Check to make sure you are using the PROG connector, not the DIAG connector, on the
programming cable.
Check both ends of the programming cable to ensure that they are firmly plugged into
the PC and the programming port on the RCM2100.
Ensure that the RCM2100 module is firmly and correctly installed in its connectors on
the Prototyping Board.
Select a different COM port within Dynamic C. From the Options menu, select
Project Options
, then select Communications. Select another COM port from the list,
then click OK. Press <Ctrl-Y> to force Dynamic C to recompile the BIOS. If Dynamic C
still reports it is unable to locate the target system, repeat the above steps until you locate
the active COM port.
相關PDF資料
PDF描述
0982660965 CBL 27PS 0.5MM JMPR TYPE A 1.18"
GEC19DRTN-S734 CONN EDGECARD 38POS DIP .100 SLD
0982660964 CBL 27PS 0.5MM JMPR TYPE D 1.18"
SRR6038-820Y INDUCTOR POWER 82UH .70A SMD
TCMD-22-T-12.00-01-N CABLE ASSEM 2MM 44POS M-F 12"
相關代理商/技術參數
參數描述
101-0433-000 制造商:ITT Interconnect Solutions 功能描述:INSUL CA-KE18-4P RR / 101-0433-000 / Circular
101-0434 功能描述:模塊化系統 - SOM RCM2100 RABBITCORE RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
101-0434-000 制造商:ITT Interconnect Solutions 功能描述:INSUL CA-KE18-4S FR / 101-0434-000 / Circular
101-0435 功能描述:模塊化系統 - SOM RCM2110 RABBITCORE RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
101-0435-000 制造商:ITT Interconnect Solutions 功能描述:INSUL CA-KE18-4S RR / 101-0435-000 / Circular
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*