- 您現在的位置：買賣IC網 > PDF目錄372964 > Z86L7208PSC (ZILOG INC) IR MICROCONTROLLER PDF資料下載
參數資料
| 型號： | Z86L7208PSC |
| 廠商： | ZILOG INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | IR MICROCONTROLLER |
| 中文描述： | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP40 |
| 封裝： | DIP-40 |
| 文件頁數： | 40/71頁 |
| 文件大?。?/td> | 364K |
| 代理商： | Z86L7208PSC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁
Z86C72/C92/L72/L92
IR Microcontroller
Zilog
6-40
P R E L I M I N A R Y
DS97LVO0900
FUNCTIONAL DESCRIPTION
(Continued)
Input Circuit
The edge detector monitors the input signal on P31 or P20.
Based on CTR1 D5-D4, a pulse is generated at the Pos
Edge or Neg Edge line when an edge is detected. Glitches
in the input signal which have a width less than specified
(CTR1 D3, D2) are filtered out.
T8 Transmit Mode
When T8 is enabled, the output of T8 depends on CTR1,
D1. If it is 0, T8_OUT is 1. If it is 1, T8_OUT is 0.
When T8 is enabled, the output T8_OUT switches to the
initial value (CTR1 D1). If the initial value (CTR1 D1) is 0,
TC8L is loaded, otherwise TC8H is loaded into the
counter. In Single-Pass Mode (CTR0 D6), T8 counts down
to 0 and stops, T8_OUT toggles, the time-out status bit
(CTR0 D5) is set, and a time-out interrupt can be generat-
ed if it is enabled (CTR0 D1) (Figure 24). In Modulo-N
Mode, upon reaching terminal count, T8_OUT is toggled,
but no interrupt is generated. Then T8 loads a new count
(if the T8_OUT level now is 0), TC8L is loaded; if it is 1,
TC8H is loaded. T8 counts down to 0, toggles T8_OUT,
sets the time-out status bit (CTR0 D5) and generates an
interrupt if enabled (CTR0 D1) (Figure 25). This completes
one cycle. T8 then loads from TC8H or TC8L according to
the T8_OUT level, and repeats the cycle.
The user can modify the values in TC8H or TC8L at any
time. The new values take effect when they are loaded.
Care must be taken not to write these registers at the time
the values are to be loaded into the counter/timer, to en-
sure known operation.
An initial count of 1 is not al-
lowed (a non-function will occur).
An initial count of 0
will cause TC8 to count from 0 to %FF to %FE (Note, % is
used for hexadecimal values). Transition from 0 to %FF is
not a time-out condition.
Note:
Using the same instructions for stopping the
counter/timers and setting the status bits is not rec-
ommended.
Two successive commands, first stopping
the counter/timers, then resetting the status bits is neces-
sary. This is required because it takes one counter/timer
clock interval for the initiated event to actually occur.
Figure 24. T8_OUT in Single-Pass Mode
TC8H Counts
“Counter Enable” Command,
T8_OUT Switches To Its
Initial Value (CTR1 D1)
T8_OUT Toggles,
Time-Out Interrupt
Figure 25. T8_OUT in Modulo-N Mode
“Counter Enable” Command,
T8_OUT Switches To Its
Initial Value (CTR1 D1)
T8_OUT Toggles
T8_OUT
TC8L
TC8H
TC8L
TC8H
TC8L
Time-Out Interrupt
Time-Out Interrupt
相關PDF資料 |
PDF描述 |
|---|---|
| Z86L7208VSC | IR MICROCONTROLLER |
| Z86C7216VSC | IR MICROCONTROLLER |
| Z86C72 | IR MICROCONTROLLER |
| Z86C7216PSC | IR MICROCONTROLLER |
| Z86C92 | IR MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| Z86L72-08PSC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| Z86L7208VSC | 制造商:ZILOG 制造商全稱:ZILOG 功能描述:IR MICROCONTROLLER |
| Z86L72-08VSC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| Z86L73 | 制造商:ZILOG 制造商全稱:ZILOG 功能描述:IR / LOW - VOLTAGE MICROCONTROLLER |
| Z86L7308FSC | 制造商:ZILOG 制造商全稱:ZILOG 功能描述:IR / LOW - VOLTAGE MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。