參數資料
型號： Z86C9216VSC
廠商： ZILOG INC
元件分類： 微控制器/微處理器
英文描述： IR MICROCONTROLLER
中文描述： 8-BIT, 16 MHz, MICROCONTROLLER, PQCC44
封裝： PLASTIC, LCC-44
文件頁數： 40/71頁
文件大小： 364K
代理商： Z86C9216VSC
Z86C72/C92/L72/L92
IR Microcontroller
Zilog
6-40
P R E L I M I N A R Y
DS97LVO0900
FUNCTIONAL DESCRIPTION
(Continued)
Input Circuit
The edge detector monitors the input signal on P31 or P20.
Based on CTR1 D5-D4, a pulse is generated at the Pos
Edge or Neg Edge line when an edge is detected. Glitches
in the input signal which have a width less than specified
(CTR1 D3, D2) are filtered out.
T8 Transmit Mode
When T8 is enabled, the output of T8 depends on CTR1,
D1. If it is 0, T8_OUT is 1. If it is 1, T8_OUT is 0.
When T8 is enabled, the output T8_OUT switches to the
initial value (CTR1 D1). If the initial value (CTR1 D1) is 0,
TC8L is loaded, otherwise TC8H is loaded into the
counter. In Single-Pass Mode (CTR0 D6), T8 counts down
to 0 and stops, T8_OUT toggles, the time-out status bit
(CTR0 D5) is set, and a time-out interrupt can be generat-
ed if it is enabled (CTR0 D1) (Figure 24). In Modulo-N
Mode, upon reaching terminal count, T8_OUT is toggled,
but no interrupt is generated. Then T8 loads a new count
(if the T8_OUT level now is 0), TC8L is loaded; if it is 1,
TC8H is loaded. T8 counts down to 0, toggles T8_OUT,
sets the time-out status bit (CTR0 D5) and generates an
interrupt if enabled (CTR0 D1) (Figure 25). This completes
one cycle. T8 then loads from TC8H or TC8L according to
the T8_OUT level, and repeats the cycle.
The user can modify the values in TC8H or TC8L at any
time. The new values take effect when they are loaded.
Care must be taken not to write these registers at the time
the values are to be loaded into the counter/timer, to en-
sure known operation.
An initial count of 1 is not al-
lowed (a non-function will occur).
An initial count of 0
will cause TC8 to count from 0 to %FF to %FE (Note, % is
used for hexadecimal values). Transition from 0 to %FF is
not a time-out condition.
Note:
Using the same instructions for stopping the
counter/timers and setting the status bits is not rec-
ommended.
Two successive commands, first stopping
the counter/timers, then resetting the status bits is neces-
sary. This is required because it takes one counter/timer
clock interval for the initiated event to actually occur.
Figure 24. T8_OUT in Single-Pass Mode
TC8H Counts
“Counter Enable” Command,
T8_OUT Switches To Its
Initial Value (CTR1 D1)
T8_OUT Toggles,
Time-Out Interrupt
Figure 25. T8_OUT in Modulo-N Mode
“Counter Enable” Command,
T8_OUT Switches To Its
Initial Value (CTR1 D1)
T8_OUT Toggles
T8_OUT
TC8L
TC8H
TC8L
TC8H
TC8L
Time-Out Interrupt
Time-Out Interrupt
相關PDF資料
PDF描述
Z86L92 IR MICROCONTROLLER
Z86L9208VSC IR MICROCONTROLLER
Z87200 CAP 0.047UF 100V 10% X7R AXIAL TR-14
ZA3020 2A STEP DOWN PWM SWITCH MODE DC DC REGULATORS
ZA3020DS 2A STEP DOWN PWM SWITCH MODE DC DC REGULATORS
相關代理商/技術參數
參數描述
Z86C92-16VSC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
Z86C93 制造商:ZILOG 制造商全稱:ZILOG 功能描述:CMOS Z8 MULT/DIV MICROCONTROLLER
Z86C9300ZEM 功能描述:仿真器/模擬器 Z8 In-Circuit Em-C93 RoHS:否 制造商:Blackhawk 產品:System Trace Emulators 工具用于評估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2
Z86C9320ASC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller
Z86C9320ASG 功能描述:8位微控制器 -MCU Z8 20 MHZ MULT/DIV ROMLESS C93 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*