參數資料
型號: XRT75L04
廠商: Exar Corporation
英文描述: FOUR CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
中文描述: 四通道E3/DS3/STS-1線路接口單元,其抖動
文件頁數: 11/57頁
文件大?。?/td> 345K
代理商: XRT75L04
XRT75L04
9
REV. 1.0.4
FOUR CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
CLOCK INTERFACE
P
IN
#
S
IGNAL
N
AME
T
YPE
D
ESCRIPTION
69
E3CLK
I
E3 Clock Input (34.368 MHz ± 20 ppm):
If any of the channels is configured in E3 mode, a reference clock 34.368 MHz
is applied on this pin.
N
OTE
:
In single frequency mode, this reference clock is not required.
67
DS3CLK
I
DS3 Clock Input (44.736 MHz ± 20 ppm):
If any of the channels is configured in DS3 mode, a reference clock 44.736
MHz. is applied on this pin.
N
OTE
:
In single frequency mode, this reference clock is not required.
65
STS-1CLK/ 12M
I
STS-1 Clock Input (51.84 MHz ± 20 ppm):
If any of the channels is configured in STS-1 mode, a reference clock 51.84
MHz is applied on this pin..
In Single Frequency Mode, a reference clock of 12.288 MHz ± 20 ppm is con-
nected to this pin and the internal clock synthesizer generates the appropriate
clock frequencies based on the configuration of the channels in E3, DS3 or
STS-1.
156
SFM_EN
I
Single Frequency Mode Enable:
Tie this pin “High” to enable the Single Frequency Mode. A reference clock of
12.288 MHz ± 20 ppm is applied. This offers the flexibility of using a low cost
reference clock and configures the board for either E3 or DS3 or STS-1 without
the need to change any components on the board.
In the Single Frequency Mode (SFM) an output clock is provided for each chan-
nel if the CLK_EN bit is set thus eliminating the need for a separate clock
source for the framer.
Tie this pin “Low” if single frequency mode is not selected. In this case, the
appropriate reference clocks must be provided.
N
OTE
:
This pin is internally pulled down
57
54
164
167
CLKOUTEN_0
CLKOUTEN_1
CLKOUTEN_2
CLKOUTEN_3
O
Clock output enable for channel 0
Clock output enable for channel 1
Clock output enable for channel 2
Clock output enable for channel 3
Pull this pin “High” to output low jitter clock on the CLKOUT_n pins.
N
OTES
:
1.
This clock output is only available in SFM mode.
2.
The maximum drive capability for the clockouts is 16 mA.
60
63
161
158
CLKOUT_0
CLKOUT_1
CLKOUT_2
CLKOUT_3
O
Clock output for channel 0
Clock output for channel 1
Clock output for channel 2
Clock output for channel 3
If CLKOUTEN_n pin is “High”, low jitter clock is output for each channel. Fre-
quency of these clocks is based on the mode (E3,DS3 or STS-1) the channels
are configured.
This eliminates the need for a separate clock source for the framer.
N
OTES
:
1.
This clock output is only available in SFM mode.
2.
The maximum drive capability for the clockouts is 16 mA.
相關PDF資料
PDF描述
XRT75L04IV FOUR CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
XRT75L06D SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
XRT75L06DIB SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
XRT75L06 SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75L06IB SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
相關代理商/技術參數
參數描述
XRT75L04D 制造商:EXAR 制造商全稱:EXAR 功能描述:FOUR CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
XRT75L04DES 功能描述:時鐘合成器/抖動清除器 4CH T3/E3/STS1 LIU+DESYNCH 3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75L04DIV 功能描述:外圍驅動器與原件 - PCI 4 CHNL E3/DS3/STS 1 JITTER ATTENUATOR RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT75L04DIV-F 功能描述:外圍驅動器與原件 - PCI 4-Ch DS3, E3, STS-1 RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT75L04DIVTR 功能描述:時鐘合成器/抖動清除器 4 CHNL E3/DS3/STS 1 JITTER ATTENUATOR RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel