參數資料
型號： XRT73LC04AIV
廠商： EXAR CORP
元件分類： 數字傳輸電路
英文描述： 4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
中文描述： DATACOM, PCM TRANSCEIVER, PQFP144
封裝： 20 X 20 MM, 1.40 MM HEIGHT, TQFP-144
文件頁數： 14/64頁
文件大?。?/td> 360K
代理商： XRT73LC04AIV
XRT73LC04A
4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
REV. 1.0.1
10
60
54
120
126
RNEG_0/(LCV_0)
RNEG_1/(LCV_1)
RNEG_2/(LCV_2)
RNEG_3/(LCV_3)
O
Line Code Violation - Channel (n):
The function of this pin is dependent on whether the XRT73LC04A is in
the Hardware or HOST Mode (HOST/HW) and if CS/(SR/DR) is set
“High”.
Hardware Mode
Line Code Violation:
When CS/(SR/DR) is set “High”, (Single-Rail operation), the B3ZS/HDB3
Encoder/Decoder is activated and the Line Code Violation signal is out-
put on this pin.
HOST Mode
Receive Negative Data:
Writing a “1” to (SR/DR)_(n) bit of the Command Register configures the
Single-Rail Mode and activates LCV_(n).
If the B3ZS/HDB3 Decoder is enabled then the zero suppression pat-
terns in the incoming line signal (such as: "00V", "000V", "B0V", "B00V")
is not reflected at this output.
74
ICT
I
In-Circuit Test Input
:
Setting this pin "Low" causes all digital and analog outputs to go into a
high-impedance state to allow for in-circuit testing. This pin should be
set to "High" for normal operation.
This pin is internally pulled "High".
75
LOSTHR
I
Loss of Signal Threshold Control
:
Forcing the LOSTHR pin to GND or VDD provides two settings. This pin
must be set to a “High” or “Low” level upon power up and should not be
changed during operation.
This pin is only applicable during DS3 or STS-1 operations.
76
84
105
97
LLB_0
LLB_1
LLB_2
LLB_3
I
Local Loop-back - Channel (n)
:
This input pin along with RLB_(n) dictates which Loop-Back mode Chan-
nel (n) is operating in.
A "High" on this pin with RLB_(n) set to "Low" configures Channel (n) to
operate in the Analog Local Loop-Back Mode.
A "High" on this pin with RLB_(n) also being set to "High" configures
Channel (n) to operate in the Digital Local Loop-Back Mode.
N
OTE
:
This pin is ignored and should be tied to GND if the XRT73LC04A
is going to be operating in the HOST Mode.
77
85
104
96
RLB_0
RLB_1
RLB_2
RLB_3
I
Remote Loop-Back - Channel (n):
This input pin in conjunction with LLB_(n) dictates which Loop-Back
mode Channel (n) is operating in.
A "High" on this pin with LLB_(n) being set to "Low" configures Channel
(n) to operate in the Remote Loop-Back Mode.
A "High" on this pin with LLB_(n) also being set to "High" configures
Channel (n) to operate in the Digital Local Loop-Back Mode.
N
OTE
:
This pin is ignored and should be tied to GND if the XRT73LC04A
is going to be operating in the HOST Mode.
CONTROL AND ALARM INTERFACE
P
IN
#
N
AME
T
YPE
D
ESCRIPTION
相關PDF資料
PDF描述
XRT73R06 SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73R06IB SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73R12 TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73R12IB TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT74L73 3 CHANNEL, ATM UNI/PPP DS3/E3 FRAMING CONTROLLER
相關代理商/技術參數
參數描述
XRT73LC04AIV-F 功能描述:外圍驅動器與原件 - PCI 4-Ch DS3, E3, STS-1 RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT73R06 制造商:EXAR 制造商全稱:EXAR 功能描述:SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73R06ES 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT73R06IB 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT73R06IB-F 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*