- 您現在的位置：買賣IC網 > PDF目錄9997 > XRT7300IVTR (Exar Corporation)IC LIU E3/DS3/STS-1 SGL 44TQFP PDF資料下載
參數資料
| 型號： | XRT7300IVTR |
| 廠商： | Exar Corporation |
| 文件頁數： | 53/55頁 |
| 文件大小： | 0K |
| 描述： | IC LIU E3/DS3/STS-1 SGL 44TQFP |
| 標準包裝： | 1,000 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 1/1 |
| 規程： | DS3，E3，STS-1 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LQFP |
| 供應商設備封裝： | 44-TQFP（10x10） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁
XRT7300
E3/DS3/STS-1 LINE INTERFACE UNIT
REV. 1.1.2
3
PIN DESCRIPTION
PIN #
SYMBOL
TYPE
DESCRIPTION
1
TXLEV
I
Transmit Line Build-Out Enable/Disable Select:
This input pin is used to enable or disable the Transmit Line Build-Out circuit in
the XRT7300.
Setting this pin to “High” disables the Line Build-Out circuit. In this mode, the
XRT7300 outputs partially shaped pulses onto the line via the TTIP and TRING
output pins.
Setting this pin to “Low” enables the Line Build-Out circuit. In this mode, the
XRT7300 outputs partially-shaped pulses onto the line via the TTIP and TRING
output pins.
To comply with the isolated DSX-3/STSX-1 Pulse Template Requirements per
Bellcore GR-499-Core or Bellcore GR-253-Core:
1. Set this input pin to a "1" if the cable length between the Cross-Connect and
the transmit output of the XRT7300 is greater than 225 feet.
2. Set this input pin to a "0" if the cable length between the Cross-Connect and
the transmit output of the XRT7300 is less than 225 feet.
This pin is active only if both of the following are true:
(a) The XRT7300 is configured to operate in either the DS3 or SONET STS-1
modes and
(b) The XRT7300 is configured to operate in the Hardware Mode.
NOTE: This pin should be tied to GND if the XRT7300 is to be operated in the
HOST mode.
2
TAOS
I
Transmit All Ones Select:
A “High” on this pin causes a continuous AMI all “1’s” pattern to be transmitted
onto the line. The frequency of this “1’s” pattern is determined by TCLK.
NOTES:
1. This input pin is ignored if the XRT7300 is operating in the HOST Mode.
2. Tie this pin to GND if the XRT7300 is going to be operating in the HOST
Mode.
3
VDD
****
Transmit Digital Power Supply
4
DMO
O
Drive Monitor Output:
If no transmitted AMI signal is present on MTIP and MRING input pins for
128±32 TCLK periods, then the DMO pin toggles and remains “High” until the
next AMI signal is detected.
5
GND
****
Transmit Digital GND
6
GND
****
Analog GND (Substrate)
7
GND
****
Receive Analog GND
8
RTIP
I
Receive TIP Input:
This input pin along with RRING is used to receive the line signal from the
Remote DS3/E3/STS-1 Terminal.
9
RRING
I
Receive RING Input:
This input pin along with RTIP is used to receive the line signal from the Remote
DS3/E3/STS-1 Terminal.
10
VDD
****
Receive Analog VDD
相關PDF資料 |
PDF描述 |
|---|---|
| MS3101E28-18SW | CONN RCPT 12POS FREE HNG W/SCKT |
| XRT73L02MIVTR-F | IC LIU E3/DS3/STS-1 2CH 100TQFP |
| MS27508E14B5SD | CONN RCPT 5POS BOX MNT W/SCKT |
| MS3100R22-15S | CONN RCPT 6POS WALL MNT W/SCKT |
| MS27467E15F97P | CONN PLUG 12POS STRAIGHT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT7300IVTR-F | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT7302IV | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCM Transceiver |
| XRT73L00 | 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73L00A | 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73L00AES | 功能描述:界面開發工具 Eval System for XRT73L00A Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。