- 您現(xiàn)在的位置：買賣IC網 > PDF目錄2018 > XRD9816BCV-F (Exar Corporation)IC 16BIT CCD/CIS SIG PROC 48TQFP PDF資料下載
參數資料
| 型號： | XRD9816BCV-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 10/53頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC 16BIT CCD/CIS SIG PROC 48TQFP |
| 標準包裝： | 250 |
| 位數： | 16 |
| 通道數： | 3 |
| 電壓 - 電源，模擬： | 4.5 V ~ 5.5 V |
| 電壓 - 電源，數字： | 3 V ~ 5.5 V |
| 封裝/外殼： | 48-TQFP |
| 供應商設備封裝： | 48-TQFP（7x7） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
XRD9814B/9816B
18
Rev. 1.00
(Correlated Double Sampling)
Correlated double sampling is a technique used to level
shift and acquire CCD output signals whose informa-
tion is equal to the difference between consecutive
reference (black) and signal (video) samples. The CDS
process consists of three steps:
1)
Sampling and holding the reference black level.
2)
Sampling the video level.
3)
Subtracting the two samples to extract the video
information.
Once the video information has been extracted it can
be processed further through amplification and/or off-
set adjustment. Since system noise is also stored and
subtracted during the CDS process, signals with band-
widths less than half the sampling frequency will be
substantially attenuated.
In order to reject higher frequency power supply noise
which is not attenuated near the sampling frequency
the XRD9814B/9816B utilizes a fully differential input
structure.
Since the CDS process uses AC coupled inputs the
coupling capacitor must be charged to the common-
mode range of the analog front-end. This can be
accomplished by clamping the coupling capacitor to
the internal clamp voltage when the CCD is at a
reference level. This clamp may occur during each
pixel (Pixel Clamp), or at the beginning of each line
(CDS Line Clamp). If CDS Line Clamp mode is used the
input buffer (configuration register #1, PB1) must be
enabled to eliminate the effects of input bias current.
If Pixel mode is selected the input buffer is not required
or recommended.
3-Channel CDS Mode
This mode allows simultaneous CDS of the red, green
and blue inputs . Black-level sampling occurs on each
pixel and is equal to the width of the BSAMP sampling
input. The black level is held on the falling edge of
BSAMP and the PGA will immediately begin to track
the signal input until the falling edge of VSAMP.
Two VSAMP timing modes are supported to allow
additional flexibility in the VSAMP pulse width (see
timing diagrams). At the end of the video sampling
phase the difference between the reference and video
levels is inverted, amplified and offset depending on
the contents of the PGA gain and offset registers. The
RGB channels are then sequentially converted by a
high speed A/D converter. A/D converter data appears
on the data output bus after 7 ADCCLK cycles. The
green channel is synchronized on the rising edge of the
first ADCCLK after the falling edge of VSAMP. The
power-up default mode is for CDS sampling a CCD
input (Pixel Clamp, Inverting Input, No Input Buffer).
1-Channel CDS Mode
The 1-Channel CDS mode allows high-speed acquisi-
tion and processing of a single channel. The timing,
clamp and buffer configurations are similar to the 3-
channel mode described previously. To select a single
channel input the color bits of configuration register 1
must be set to the appropriate value. The A/D input will
begin to track the selected color input on the next
positive edge of ADCCLK. If the configuration is
toggled from single color to 3-channel mode RGB
scanning will not occur until the circuit is
resynchronized on the falling edge of VSAMP.
相關PDF資料 |
PDF描述 |
|---|---|
| XRD9818ACGTR | IC 16B CCD/CIS SIG PROC 28TSSOP |
| XRD9824ACU | IC 14B CCD/CIS SIG PROC 20SSOP |
| XRD9825ACU | IC 16B CCD/CIS SIG PROC 20SSOP |
| XRD9826ACUTR | IC 16B CCD/CIS SIG PROC 20SSOP |
| XRD9827ACU | IC 12B CCD/CIS SIG PROC 20SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRD9816EVAL | 功能描述:數據轉換 IC 開發(fā)工具 Eval Board for XRD9816BCV RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| XRD9818 | 制造商:EXAR 制造商全稱:EXAR 功能描述:3-CHANNEL 16-BIT LINEAR CCD/CIS SENSOR SIGNAL PROCESSOR |
| XRD9818ACG | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| XRD9818ACG-F | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| XRD9818ACGTR | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發(fā)布緊急采購，3分鐘左右您將得到回復。