Figure 44 shows two DUART devices, one labeled “Transmitting Device” and the other, “Receiving Device”. This example star" />
參數資料
型號： XR88C681CP/40-F
廠商： Exar Corporation
文件頁數： 84/101頁
文件大?。?/td> 0K
描述： IC UART CMOS DUAL 40PDIP
標準包裝： 9
特點： *
通道數： 2，DUART
FIFO's： 1 字節，3 字節
電源電壓： 4.75 V ~ 5.25 V
帶并行端口： 是
帶CMOS： 是
安裝類型： 通孔
封裝/外殼： 40-DIP（0.600"，15.24mm）
供應商設備封裝： 40-PDIP
包裝： 管件
其它名稱： 1016-1328-5
XR88C681
83
Rev. 2.11
Figure 44 shows two DUART devices, one labeled
“Transmitting Device” and the other, “Receiving Device”.
This example starts with the assumption that the
“Transmitter Device” has been programmed such that
MR2A[5] = 1, which results in programming the
“Transmitting Device” for Transmitter-RTS Control. This
example further assumes that the “Transmitting Device”
has been programmed such that MR2A[4] = 1. According
to
Section G.3, the Transmitter of Channel A of the
“Transmitting Device” has now been programmed to be
under -CTSA input control.
In the case of the “Receiving Device”, IP2 (RTS-in) has
been programmed to generate an “Input Port Change of
State” interrupt request to the CPU. The firmware for the
Interrupt Service Routines is written such that if the IP2
input were to change and IPCR[2] = 0, the CPU would
“write” [D7,..., D0] = [0, 0, 0, 0, 1, 0, 0, 0] to DUART
address 0E16. In this step, the Interrupt Service Routine
would invoke the “SET OUTPUT PORT BITS
COMMAND”, and in the process toggle OPR[3] to a logic
“high” and the Output Port pin, OP3, (CTS-out) to a logic
“l(fā)ow”. This would, in turn, assert the -CTSA input of the
“Transmitting Device” and allow it to transmit data to the
“Receiving Device”.
Once Channel A Transmitter has emptied both its THR
and TSR of data, it will negate the -RTSA output, via the
“Transmitter-RTS Control” feature. When the -RTSA
output the “Transmitting Device” is toggled “high”, the IP2
(RTS-in) is also toggled “high”, thereby generating
another “Input Change of State” interrupt request to the
CPU. With IPCR[2] = 1, the likely Interrupt Service
Routine would be to “Write” [D7,..., D0] = [0, 0, 0, 0, 1, 0, 0,
0] to DUART address 0F16. In this step, the Interrupt
Service Routine would invoke the “CLEAR OUTPUT
PORT BITS COMMAND”, and in the process toggle OP3
(CTS-out) “high”. This would in turn negate the -CTSA
input of the “Transmitting Device” and inhibit the
transmission of data from the Channel A of the
“Transmitting Device”.
Figure 45 presents a Flow Diagram which depicts an
Algorithm that could be used to implement the
Transmitter-Control RTS/CTS Handshaking Mode.
Please note that the shaded block pertain to occurrences
within the “Receiving Device”. Whereas the “White” block
pertain to operation within the “Transmitting Device.”
相關PDF資料
PDF描述
AT89C51RB2-RLRIM IC MCU FLASH 8051 16K 5V 44-VQFP
XR16V2550IM-F IC UART FIFO 16B 48TQFP
MAX7311AWG+T IC I/O EXPANDER I2C 16B 24SOIC
XR16L2750CM-F IC UART FIFO 64B DUAL 48TQFP
XR20M1172IL32-F IC UART FIFO I2C/SPI 64B 32QFN
相關代理商/技術參數
參數描述
XR88C681J 制造商:Exar Corporation 功能描述:
XR88C681J-F 功能描述:UART 接口集成電路 0.5V-2V UART temp -45 to 85C RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR88C681JTR-F 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR88C681MN-S0968 制造商:Exar Corporation 功能描述:
XR88C681N/40 制造商:EXAR 制造商全稱:EXAR 功能描述:CMOS DUAL CHANNEL UART (DUART)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*