參數資料
型號： XR88C681CJ-F
廠商： Exar Corporation
文件頁數： 11/101頁
文件大?。?/td> 0K
描述： IC UART CMOS DUAL 44PLCC
標準包裝： 27
特點： *
通道數： 2，DUART
FIFO's： 1 字節，3 字節
電源電壓： 4.75 V ~ 5.25 V
帶并行端口： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 44-LCC（J 形引線）
供應商設備封裝： 44-PLCC（16.59x16.59）
包裝： 管件
其它名稱： 1016-1327-5
XR88C681
17
Rev. 2.11
Bit 7
Bit 6
Bit 5
Bit 4
Description
0
1
0
Reset Error Status.
Clears the Received Break
(RB), Parity Error (PE), Framing Error (FE) and
Overrun Error (OE) status bits, SR[7:3].
Specifically, if the Error Mode, for a particular chan-
nel is set at “Block” Error Mode, this command will
reset all of the Receiver Error Indicators in the Status
Register. In the Block Error Mode, once either a PE,
FE, OE, or RB occurs, the error will continue to be
flagged in the Status Register, until this command is
issued.
If the Error Mode, for a particular channel is set to
“Character Error Mode”, then the contents of the
Status Register for PE, FE, and RB are reflected on
a character by character basis. In the “Character
Error Mode”, the state of these indicators is based
only upon the character that is at the top of the RHR.
The OE indicator is always presented as a “Block
Error Mode” indicator, and requires this command to
be reset.
0
1
0
1
Reset Break Change Interrupt.
Clears the chan-
nel’s break change interrupt status bit.
0
1
0
Start Break.
Forces the TXDn output low. The
transmitter must be enabled to start a break. If the
transmitter is empty, the start of the break may be
delayed up to two bit times. If the transmitter is ac-
tive, the break begins when the transmission of
those characters in the THR is completed, viz.,
TXEMP must be true before the break will begin.
0
1
Stop Break.
The TXDn line will go high within two
bit times. TXDn will remain high for one bit time be-
fore the next character, if any, is transmitted.
1
0
Set Rx BRG Select Extend Bit.
Sets the channel’s
“Receiver BRG Select Extend Bit” to 1.
1
0
1
Clear Rx BRG Select Extend Bit.
Clears the chan-
nel’s “Receiver BRG Select Extend Bit” to 0.
1
0
1
0
Set Tx BRG Select Extend Bit.
Sets the channel’s
“Transmitter BRG Select Extend Bit” to 1.
1
0
1
Clear Tx BRG Select Extend Bit.
Clears the chan-
nel’s “Transmitter BRG Select Extend Bit” to 0.
Table 3. Miscellaneous Commands, Upper Nibble of all Command Registers,
Unless Otherwise Specified (Cont’d)
相關PDF資料
PDF描述
XR16M2550IM48-F IC UART FIFO 16B 1.8V DL 48TQFP
ST16C552CJ68-F IC UART FIFO PAR 16B DUAL 68PLCC
XR16L2752IJ-F IC UART FIFO 64B DUAL 44PLCC
ST16C552IJ68-F IC UART FIFO 16B DUAL 68PLCC
XR88C92IJ-F IC UART FIFO DUAL 44PLCC
相關代理商/技術參數
參數描述
XR88C681CJTR-F 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR88C681CN/40 制造商:EXAR 制造商全稱:EXAR 功能描述:CMOS DUAL CHANNEL UART (DUART)
XR88C681CP/28 制造商:EXAR 制造商全稱:EXAR 功能描述:CMOS DUAL CHANNEL UART (DUART)
XR88C681CP/28-F 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR88C681CP/40 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*