參數資料
型號： XR20M1172IG28-F
廠商： Exar Corporation
文件頁數： 31/55頁
文件大小： 0K
描述： IC UART FIFO I2C/SPI 64B 28TSSOP
產品培訓模塊： UART Product Overview
標準包裝： 50
特點： *
通道數： 2，DUART
FIFO's： 64 字節
規程： RS485
電源電壓： 1.62 V ~ 3.63 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 28-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 28-TSSOP
包裝： 管件
其它名稱： 1016-1298-5
XR20M1172
37
REV. 1.2.0
TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO
MSR[7]: CD Input Status
Normally this bit is the complement of the CD# input. In the loopback mode this bit is equivalent to bit-3 in the
MCR register. The CD# input may be used as a general purpose input when the modem interface is not used.
4.10
Scratch Pad Register (SPR) - Read/Write
This is a 8-bit general purpose register for the user to store temporary data. The content of this register is
preserved during sleep mode but becomes 0xFF (default) after a reset or a power off-on cycle. There are also
two other registers (TLR and FIFO Rdy) that share the same address location as the Scratch Pad Register.
See Table 13.
4.11
Transmission Control Register (TCR) - Read/Write (requires EFR bit-4 = 1)
This register replaces MSR and is accessible only when MCR[6] = 1. This 8-bit register is used to store the RX
FIFO threshold levels to halt/resume transmission during hardware or software flow control.
TCR[3:0]: RX FIFO Halt Level
A value of 0-60 (decimal value of TCR[3:0] multiplied by 4) can be selected as the Halt Level. When the RX
FIFO is greater than or equal to this value, the RTS# output will be de-asserted if Auto RTS flow control is used
or the XOFF character(s) will be transmitted if Auto XON/XOFF flow control is used. It is recommended that
this value is greater than the RX Trigger Level.
TCR[7:4]: RX FIFO Resume Level
A value of 0-60 (decimal value of TCR[7:4] multiplied by 4) can be selected as the Resume Level. When the
RX FIFO is less than or equal to this value, the RTS# output will be re-asserted if Auto RTS flow control is used
or the XON character(s) will be transmitted if Auto XON/XOFF flow control is used. It is recommended that this
value is less than the RX Trigger Level.
4.12
Trigger Level Register (TLR) - Read/Write (requires EFR bit-4 = 1)
This register replaces SPR and is accessible under the conditions listed in Table 13. This 8-bit register is used
to store the RX and TX FIFO trigger levels used for interrupts.
TLR[3:0]: TX FIFO Trigger Level
A value of 4-60 (decimal value of TCR[3:0] multiplied by 4) can be selected as the TX FIFO Trigger Level.
When the number of available spaces in the TX FIFO is greater than or equal to this value, a Transmit Ready
interrupt is generated. For any non-zero value, TCR[3:0] will be used as the TX FIFO Trigger Level.
If
TCR[3:0] = 0x0, then the TX FIFO Trigger Level is the value selected by FCR[5:4]. See Table 10.
TLR[7:4]: RX FIFO Trigger Level
A value of 4-60 (decimal value of TCR[7:4] multiplied by 4) can be selected as the RX FIFO Trigger Level.
When the number of characters received in the RX FIFO is greater than or equal to this value, a Receive Data
Ready interrupt is generated (a Receive Data Timeout interrupt is independent of the RX FIFO Trigger Level
and can be generated any time there is at least 1 byte in the RX FIFO and the RX input has been idle for the
timeout period described in “Section 2.8, Receiver” on page 17). For any non-zero value, TCR[7:4] will be
used as the RX FIFO Trigger Level. If TCR[7:4] = 0x0, then the RX FIFO Trigger Level is the value selected by
FCR[7:6]. See Table 10.
4.13
Transmit FIFO Level Register (TXLVL) - Read-only
This register reports the number of spaces available in the TX FIFO. If the TX FIFO is empty, the TXLVL
register will report that there are 64 spaces available. If the TX FIFO is full, the TXLVL register will report that
there are 0 spaces available.
4.14
Receive FIFO Level Register (RXLVL) - Read-only
This register reports the number of characters available in the RX FIFO. If the RX FIFO is empty, the RXLVL
register will report that there are 0 characters available. If the RX FIFO is full, the RXLVL register will report
that there are 64 characcters available.
相關PDF資料
PDF描述
XR20M1280IL40-F IC UART I2C/SPI 128 BYTE 40QFN
XR20V2170IL40-F IC UART/TXRX I2C/SPI RS232 40QFN
XR20V2172IL64-F IC UART/TXRX I2C/SPI RS232 64QFN
XR21V1410IL16TR-F IC USB UART FIFO FULL SPD 16QFN
XR21V1412IL32TR-F IC USB UART FIFO FULL SPD 32QFN
相關代理商/技術參數
參數描述
XR20M1172IG28-F 制造商:Exar Corporation 功能描述:IC DUAL UART 16MBPS 3.63V 28-TSSOP 制造商:Exar Corporation 功能描述:IC, DUAL UART, 16MBPS, 3.63V, 28-TSSOP
XR20M1172IG28TR-F 功能描述:UART 接口集成電路 1.8V 2 Ch 64-byte I2C/SPI UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR20M1172IL32 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO
XR20M1172IL32-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR20M1172IL32-F 制造商:Exar Corporation 功能描述:IC DUAL UART 16MBPS 3.63V 32-QFN
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*