- 您現在的位置：買賣IC網 > PDF目錄16531 > XR19L210IL40-0A-EB (Exar Corporation)EVAL BOARD FOR XR19L202 40QFN PDF資料下載
參數資料
| 型號： | XR19L210IL40-0A-EB |
| 廠商： | Exar Corporation |
| 文件頁數： | 4/43頁 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR XR19L202 40QFN |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
XR19L210
12
SINGLE CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER
REV. 1.0.2
2.12
Auto RTS (Hardware) Flow Control
Automatic RTS hardware flow control is used to prevent data overrun to the local receiver FIFO. The RTS
output is used to request remote unit to suspend/resume data transmission. The auto RTS flow control
features is enabled to fit specific application requirement (see Figure 10):
Enable auto RTS flow control using EFR bit-6.
The auto RTS function must be started by asserting RTS output pin (MCR bit-1 to logic 1 after it is enabled).
If using the Auto RTS interrupt:
Enable RTS interrupt through IER bit-6 (after setting EFR bit-4). The UART issues an interrupt when the RTS
pin makes a transition from low to high: ISR bit-5 will be set to logic 1.
2.13
Auto RTS Hysteresis
The L210 has a new feature that provides flow control trigger hysteresis while maintaining compatibility with
the ST16C550 UART. With the Auto RTS function enabled, an interrupt is generated when the receive FIFO
reaches the programmed RX trigger level. The RTS pin will not be de-asserted until the receive FIFO reaches
one trigger level above the programmed trigger level in the trigger table (Table 8). The RTS pin will be re-
asserted after the RX FIFO is unloaded to one trigger level lower than the programmed trigger level. This is
described in Figure 10. Under the above described conditions, the L210 will continue to accept data until the
receive FIFO gets full. The Auto RTS function is initiated when the RTS output pin is asserted.
2.14
Auto CTS Flow Control
Automatic CTS flow control is used to prevent data overrun to the remote receiver FIFO. The CTS input is
monitored to suspend/restart the local transmitter. The auto CTS flow control feature is selected to fit specific
application requirement (see Figure 10):
Enable auto CTS flow control using EFR bit-7.
If using the Auto CTS interrupt:
Enable CTS interrupt through IER bit-7 (after setting EFR bit-4). The UART issues an interrupt when the CTS
pin is de-asserted: ISR bit-5 will be set to 1, and UART will suspend transmission as soon as the stop bit of
the character in process is shifted out. Transmission is resumed after the CTS input is re-asserted, indicating
more data may be sent.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-JTT-EZ-S | CONVERTER MOD DC/DC 6.5V 25W |
| 6374109-7 | C/A 62.5/125 1.6MM LC 0.34M |
| XR19L200IL32-0A-EB | EVAL BOARD FOR XR19L200 32QFN |
| 6374611-1 | C/A 2.0MM SM LC-SC 1M1 |
| RBC15DCST-S288 | CONN EDGECARD 30POS .100 EXTEND |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR19L210IL40-0B-EB | 功能描述:界面開發(fā)工具 Supports L210 40 pin QFN, PCI Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR19L210IL40-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR19L212 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER |
| XR19L212IL48 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER |
| XR19L212IL48-0B-EB | 功能描述:界面開發(fā)工具 Supports L212 48 pin QFN, PCI Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發(fā)布緊急采購，3分鐘左右您將得到回復。