REV. 1.0.3 MCR[3]: INT Output Enable Enable or disable INT outputs to become active " />
參數資料
型號： XR16V554IV-0A-EVB
廠商： Exar Corporation
文件頁數： 19/43頁
文件大?。?/td> 0K
描述： EVAL BOARD FOR XR16V554 64LQFP
標準包裝： 1
系列： *
XR16V554/554D
26
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.3
MCR[3]: INT Output Enable
Enable or disable INT outputs to become active or in three-state. This function is associated with the INTSEL
input, see below table for details. This bit is also used to control the OP2# signal during internal loopback
mode. INTSEL pin must be LOW during 68 mode.
Logic 0 = INT (A-D) outputs disabled (three state) in the 16 mode (default). During internal loopback mode,
OP2# is HIGH.
Logic 1 = INT (A-D) outputs enabled (active) in the 16 mode. During internal loopback mode, OP2# is LOW.
TABLE 12: INT OUTPUT MODES
PIN
BIT-3
INT A-D OUTPUTS IN 16 MODE
0
Three-State
0
1
Active
1
X
Active
MCR[4]: Internal Loopback Enable
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and Figure 11.
MCR[7:5]: Reserved
4.8
Line Status Register (LSR) - Read/Write
This register is writeable but it is not recommended. The LSR provides the status of data transfers between the
UART and the host. If IER bit-2 is enabled, LSR bit-1 will generate an interrupt immediately and LSR bits 2-4
will generate an interrupt when a character with an error is in the RHR.
LSR[0]: Receive Data Ready Indicator
Logic 0 = No data in receive holding register or FIFO (default).
Logic 1 = Data has been received and is saved in the receive holding register or FIFO.
LSR[1]: Receiver Overrun Flag
Logic 0 = No overrun error (default).
Logic 1 = Overrun error. A data overrun error condition occurred in the receive shift register. This happens
when additional data arrives while the FIFO is full. In this case the previous data in the receive shift register
is overwritten. Note that under this condition the data byte in the receive shift register is not transferred into
the FIFO, therefore the data in the FIFO is not corrupted by the error.
LSR[2]: Receive Data Parity Error Tag
Logic 0 = No parity error (default).
Logic 1 = Parity error. The receive character in RHR does not have correct parity information and is suspect.
This error is associated with the character available for reading in RHR.
LSR[3]: Receive Data Framing Error Tag
Logic 0 = No framing error (default).
Logic 1 = Framing error. The receive character did not have a valid stop bit(s). This error is associated with
the character available for reading in RHR.
INTSEL
MCR
相關PDF資料
PDF描述
5492191-1 CA SM LDS SCAPC-SC/UPC(NG)
LB2016T680M INDUCTOR WOUND 68UH 55MA 0806
1-6374613-2 C/A LC-SC DUP 50/125 MM 12M
SI5013-EVB BOARD EVALUATION FOR SI5013
GBC18DRTI-S734 CONN EDGECARD 36POS DIP .100 SLD
相關代理商/技術參數
參數描述
XR16V554IV80 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
XR16V554IV80-0A-EB 功能描述:界面開發工具 Supports V554 80 ld LQFP,ISA Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR16V554IV80-F 功能描述:UART 接口集成電路 2.25V-3.6V 16B FIFO temp -45 to 85C;UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16V554IV80TR-F 功能描述:UART 接口集成電路 XR16V554IV80TR-F RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16V554IV-F 功能描述:通用總線函數 UART RoHS:否 制造商:Texas Instruments 邏輯類型:CMOS 邏輯系列:74VMEH 電路數量:1 開啟電阻（最大值）: 傳播延遲時間:10.1 ns 電源電壓-最大:3.45 V 電源電壓-最小:3.15 V 最大工作溫度:+ 85 C 最小工作溫度:0 C 封裝 / 箱體:TSSOP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*