- 您現在的位置：買賣IC網 > PDF目錄16492 > XR16V554IV-0A-EVB (Exar Corporation)EVAL BOARD FOR XR16V554 64LQFP PDF資料下載
參數資料
| 型號： | XR16V554IV-0A-EVB |
| 廠商： | Exar Corporation |
| 文件頁數： | 18/43頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR XR16V554 64LQFP |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
XR16V554/554D
25
REV. 1.0.3
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
LCR[5]: TX and RX Parity Select
If the parity bit is enabled, LCR BIT-5 selects the forced parity format.
LCR BIT-5 = logic 0, parity is not forced (default).
LCR BIT-5 = logic 1 and LCR BIT-4 = logic 0, parity bit is forced to HIGH for the transmit and receive data.
LCR BIT-5 = logic 1 and LCR BIT-4 = logic 1, parity bit is forced to LOW for the transmit and receive data.
TABLE 11: PARITY SELECTION
LCR BIT-5 LCR BIT-4 LCR BIT-3
PARITY SELECTION
X
0
No parity
0
1
Odd parity
0
1
Even parity
1
0
1
Force parity to mark, HIGH
1
Forced parity to space, LOW
LCR[6]: Transmit Break Enable
When enabled, the Break control bit causes a break condition to be transmitted (the TX output is forced to a
“space’, logic 0, state). This condition remains, until disabled by setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition. (default)
Logic 1 = Forces the transmitter output (TX) to a “space”, logic 0, for alerting the remote receiver of a line
break condition.
LCR[7]: Baud Rate Divisors Enable
Baud rate generator divisor (DLL/DLM) enable.
Logic 0 = Data registers are selected (default).
Logic 1 = Divisor latch registers are selected.
4.7
Modem Control Register (MCR) or General Purpose Outputs Control - Read/Write
The MCR register is used for controlling the serial/modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Output
The DTR# pin is a modem control output. If the modem interface is not used, this output may be used as a
general purpose output.
Logic 0 = Force DTR# output HIGH (default).
Logic 1 = Force DTR# output LOW.
MCR[1]: RTS# Output
The RTS# pin is a modem control output. If the modem interface is not used, this output may be used as a
general purpose output.
Logic 0 = Force RTS# output HIGH (default).
Logic 1 = Force RTS# output LOW.
MCR[2]: Reserved
OP1# is not available as an output pin on the V554. But it is available for use during Internal Loopback Mode.
In the Loopback Mode, this bit is used to write the state of the modem RI# interface signal.
相關PDF資料 |
PDF描述 |
|---|---|
| 5492191-1 | CA SM LDS SCAPC-SC/UPC(NG) |
| LB2016T680M | INDUCTOR WOUND 68UH 55MA 0806 |
| 1-6374613-2 | C/A LC-SC DUP 50/125 MM 12M |
| SI5013-EVB | BOARD EVALUATION FOR SI5013 |
| GBC18DRTI-S734 | CONN EDGECARD 36POS DIP .100 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16V554IV80 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO |
| XR16V554IV80-0A-EB | 功能描述:界面開發工具 Supports V554 80 ld LQFP,ISA Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR16V554IV80-F | 功能描述:UART 接口集成電路 2.25V-3.6V 16B FIFO temp -45 to 85C;UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16V554IV80TR-F | 功能描述:UART 接口集成電路 XR16V554IV80TR-F RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16V554IV-F | 功能描述:通用總線函數 UART RoHS:否 制造商:Texas Instruments 邏輯類型:CMOS 邏輯系列:74VMEH 電路數量:1 開啟電阻（最大值）: 傳播延遲時間:10.1 ns 電源電壓-最大:3.45 V 電源電壓-最小:3.15 V 最大工作溫度:+ 85 C 最小工作溫度:0 C 封裝 / 箱體:TSSOP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。