- 您現在的位置：買賣IC網 > PDF目錄16523 > XR16V2652IL-0B-EB (Exar Corporation)EVAL BOARD FOR V2652 32QFN PDF資料下載
參數資料
| 型號： | XR16V2652IL-0B-EB |
| 廠商： | Exar Corporation |
| 文件頁數： | 9/48頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR V2652 32QFN |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
XR16V2652
17
REV. 1.0.2
HIGH PERFORMANCE DUART WITH 32-BYTE FIFO
2.16
Auto Xon/Xoff (Software) Flow Control
When software flow control is enabled (See Table 14), the V2652 compares one or two sequential receive data
characters with the programmed Xon or Xoff-1,2 character value(s). If receive character(s) (RX) match the
programmed values, the V2652 will halt transmission (TX) as soon as the current character has completed
transmission. When a match occurs, the Xoff (if enabled via IER bit-5) flag will be set and the interrupt output
pin will be activated. Following a suspension due to a match of the Xoff character, the V2652 will monitor the
receive data stream for a match to the Xon-1,2 character. If a match is found, the V2652 will resume operation
and clear the flags (ISR bit-4).
Reset initially sets the contents of the Xon/Xoff 8-bit flow control registers to 0x00. Following reset the user can
write any Xon/Xoff value desired for software flow control. Different conditions can be set to detect Xon/Xoff
characters (See Table 14) and suspend/resume transmissions. When double 8-bit Xon/Xoff characters are
selected, the V2652 compares two consecutive receive characters with two software flow control 8-bit values
(Xon1, Xon2, Xoff1, Xoff2) and controls TX transmissions accordingly. Under the above described flow control
mechanisms, flow control characters are not placed (stacked) in the user accessible RX data buffer or FIFO.
In the event that the receive buffer is overfilling and flow control needs to be executed, the V2652 automatically
sends an Xoff message via the serial TX output to the remote modem. The V2652 sends the Xoff-1,2
characters two-character times (= time taken to send two characters at the programmed baud rate) after the
receive FIFO crosses the selected trigger level. To clear this condition, the V2652 will transmit the programmed
Xon-1,2 characters as soon as receive FIFO is less than one trigger level below the selected trigger level.
Table 7 below explains this.
* After the trigger level is reached, an xoff character is sent after a short span of time (= time required to send 2
characters); for example, after 2.083ms has elapsed for 9600 baud and 10-bit word length setting.
2.17
Special Character Detect
A special character detect feature is provided to detect an 8-bit character when bit-5 is set in the Enhanced
Feature Register (EFR). When this character (Xoff2) is detected, it will be placed in the FIFO along with normal
incoming RX data.
The V2652 compares each incoming receive character with Xoff-2 data. If a match exists, the received data will
be transferred to FIFO and ISR bit-4 will be set to indicate detection of special character. Although the Internal
Register Table shows Xon, Xoff Registers with eight bits of character information, the actual number of bits is
dependent on the programmed word length. Line Control Register (LCR) bits 0-1 defines the number of
character bits, i.e., either 5 bits, 6 bits, 7 bits, or 8 bits. The word length selected by LCR bits 0-1 also
determines the number of bits that will be used for the special character comparison. Bit-0 in the Xon, Xoff
Registers corresponds with the LSB bit for the receive character.
TABLE 7: AUTO XON/XOFF (SOFTWARE) FLOW CONTROL
RX TRIGGER LEVEL
INT PIN ACTIVATION
XOFF CHARACTER(S) SENT
(CHARACTERS IN RX FIFO)
XON CHARACTER(S) SENT
(CHARACTERS IN RX FIFO)
8
8*
0
16
16*
8
24
24*
16
28
28*
24
相關PDF資料 |
PDF描述 |
|---|---|
| 5022-392J | INDUCTOR 3.90UH 5% TOLERANCE SMD |
| GSM11DRTN-S13 | CONN EDGECARD 22POS .156 EXTEND |
| RCM10DTKI-S288 | CONN EDGECARD 20POS .156 EXTEND |
| A3DDB-1636G | IDC CABLE- AKR16B/AE16G/AKR16B |
| MCP1316T-29LE/OT | IC SUPERVISOR 2.90V P-P SOT23-5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16V2652IL32 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 32-BYTE FIFO |
| XR16V2652IL-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16V2652ILTR-F | 制造商:Exar Corporation 功能描述:UART 2-CH 32Byte FIFO 2.5V/3.3V 32-Pin QFN EP T/R 制造商:Exar Corporation 功能描述:XR16V2652ILTR-F |
| XR16V2750 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
| XR16V2750_07 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
發布緊急采購，3分鐘左右您將得到回復。