REV. 1.0.1 1.62V TO 3.63V HIGH PERFORMANCE UART WITH 32-BYTE FIFO an interrupt is pending from any channel. The M670 will stay in t" />
參數資料
型號: XR16M670IL24-F
廠商: Exar Corporation
文件頁數: 14/50頁
文件大?。?/td> 0K
描述: IC UART FIFO 32B 24QFN
標準包裝: 490
特點: *
通道數: 1,UART
FIFO's: 32 字節
規程: RS232,RS422,RS485
電源電壓: 1.62 V ~ 3.63 V
帶自動流量控制功能:
帶IrDA 編碼器/解碼器:
帶故障啟動位檢測功能:
帶調制解調器控制功能:
帶CMOS:
安裝類型: 表面貼裝
封裝/外殼: 24-VFQFN 裸露焊盤
供應商設備封裝: 24-QFN 裸露焊盤(4x4)
包裝: 托盤
XR16M670
21
REV. 1.0.1
1.62V TO 3.63V HIGH PERFORMANCE UART WITH 32-BYTE FIFO
an interrupt is pending from any channel. The M670 will stay in the sleep mode of operation until it is disabled
by setting IER bit-4 to a logic 0.
A word of caution: owing to the starting up delay of the crystal oscillator after waking up from sleep mode, the
first few receive characters may be lost. Also, make sure the RX pin is idling HIGH or “marking” condition
during sleep mode. This may not occur when the external interface transceivers (RS-232, RS-485 or another
type) are also put to sleep mode and cannot maintain the “marking” condition. To avoid this, the system design
engineer can use a 47k ohm pull-up resistor on each of the RX input.
2.17.2
Power-Save Feature
If the address lines, data bus lines, IOW#, IOR#, CS# and modem input lines remain steady when the M670 is
in sleep mode, the maximum current will be in the microamp range as specified in the DC Electrical
Characteristics on page 41. If the input lines are floating or are toggling while the M670 is in sleep mode, the
current can be up to 100 times more. If not using the Power-Save feature, an external buffer would be required
to keep the address and data bus lines from toggling or floating to achieve the low current. But if the Power-
Save feature is enabled (PwrSave pin connected to VCC), this will eliminate the need for an external buffer by
internally isolating the address, data and control signals (see Figure 1 on page 1) from other bus activities that
could cause wasteful power drain. The M670 enters Power-Save mode when this pin is connected to VCC and
the M670 is in sleep mode (see Sleep Mode section above).
Since Power-Save mode isolates the address, data and control signals, the device will wake-up only by:
a receive data start bit transition (HIGH to LOW) at the RX input or
a change of logic state on the modem or general purpose serial input CTS#, DSR#, CD#, RI#
The M670 will return to the Power-Save mode automatically after a read to the MSR (to reset the modem input
CTS#) and all interrupting conditions have been serviced and cleared. The M670 will stay in the Power-Save
mode of operation until it is disabled by setting IER bit-4 to a logic 0 and/or the Power-Save pin is connected to
GND.
2.17.3
Wake-up Interrupt
The M670 has the wake up interrupt. By setting the FCR bit-3, wake up interrupt is enabled or disabled. The
default status of wake up interrupt is disabled. Please See ”Section 4.5, FIFO Control Register (FCR) -
相關PDF資料
PDF描述
ST16C450CJ44TR-F IC UART SINGLE 44PLCC
XR16M780IB25-F IC UART FIFO 64B 25BGA
XR16M770IB25-F IC UART FIFO 64B 25BGA
XR19L400IL40TR-F IC UART/TXRX RS485 40QFN
XR16M680IB25-F IC UART FIFO 32B 25BGA
相關代理商/技術參數
參數描述
XR16M670IL32 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE UART WITH 32-BYTE FIFO
XR16M670IL32-0A-EB 功能描述:界面開發工具 Eval Board for XR16M670IL32 Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR16M670IL32-0B-EB 功能描述:界面開發工具 Eval Board for XR16M670IL32 Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR16M670IL32-0C-EB 功能描述:界面開發工具 Eval Board for XR16M670IL32 Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR16M670IL32-F 功能描述:UART 接口集成電路 1.8 HIGH PERFORMANCE UART W/32 RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel