參數資料
型號： XR16M2750IM-0A-EB
廠商： Exar Corporation
文件頁數： 45/53頁
文件大小： 0K
描述： EVAL BOARD FOR M2750-A 48TQFP
標準包裝： 1
系列： *
XR16M2750
5
REV. 1.0.0
1.62V TO 3.63V HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
RXB
3
4
I
UART channel B Receive Data or infrared receive data. Normal receive
data input must idle HIGH. The infrared receiver pulses typically idles at
logic 0 but can be inverted by software control prior going in to the
decoder, see MCR[6] and FCTR[2]. If this pin is not used, tie it to VCC
or pull it high via a 100k ohm resistor.
RTSB#
15
22
O
UART channel B Request-to-Send (active low) or general purpose out-
put. This port must be asserted prior to using auto RTS flow control,
see EFR[6], MCR[1], FCTR[1:0], EMSR[5:4] and IER[6]. For auto
RS485 half-duplex direction control, see FCTR[3] and EMSR[3].
CTSB#
16
23
I
UART channel B Clear-to-Send (active low) or general purpose input.
It can be used for auto CTS flow control, see EFR[7], and IER[7]. This
input should be connected to VCC when not used.
DTRB#
-
35
O
UART channel B Data-Terminal-Ready (active low) or general purpose
output. If it is not used, leave it unconnected.
DSRB#
-
20
I
UART channel B Data-Set-Ready (active low) or general purpose input.
This input should be connected to VCC when not used. This input has
no effect on the UART.
CDB#
-
16
I
UART channel B Carrier-Detect (active low) or general purpose input.
This input should be connected to VCC when not used. This input has
no effect on the UART.
RIB#
-
21
I
UART channel B Ring-Indicator (active low) or general purpose input.
This input should be connected to VCC when not used. This input has
no effect on the UART.
OP2B#
-
9
O
Output Port 2 Channel B - The output state is defined by the user and
through the software setting of MCR[3]. INTB is set to the active mode
and OP2B# output LOW when MCR[3] is set to a logic 1. INTB is set to
the three state mode and OP2B# output HIGH when MCR[3] is set to a
logic 0. See MCR[3]. If INTB is used, this output should not be used as
a general output else it will disturb the INTB output functionality.
ANCILLARY SIGNALS
XTAL1
10
13
I
Crystal or external clock input.
XTAL2
11
14
O
Crystal or buffered clock output.
RESET
24
36
I
Reset (active high) - A longer than 40 ns HIGH pulse on this pin will
reset the internal registers and all outputs. The UART transmitter output
will be held HIGH, the receiver input will be ignored and outputs are
reset during reset period (see
VCC
26
42
Pwr
1.62V to 3.63V power supply.
GND
13
17
Pwr
Power supply common, ground.
GND
Center Pad
N/A
Pwr
The center pad on the backside of the 32-QFN package is metallic and
should be connected to GND on the PCB. The thermal pad size on the
PCB should be the approximate size of this center pad and should be
solder mask defined. The solder mask opening should be at least
0.0025" inwards from the edge of the PCB thermal pad.
Pin Description
NAME
32-QFN
PIN #
48-TQFP
PIN #
TYPE
DESCRIPTION
相關PDF資料
PDF描述
ECM08DRMD-S664 CONN EDGECARD 16POS .156 WW
MFP 3/32"CR48"BX HTSHRNK MFP 3/32"X4'(8')CLR
GCA32DTKI CONN EDGECARD 64POS DIP .125 SLD
RYM10DTBS CONN EDGECARD 20POS R/A .156 SLD
5492191-4 CA SM LDS SCAPC-SC/UPC(NG)
相關代理商/技術參數
參數描述
XR16M2750IM-0B-EB 功能描述:界面開發工具 Eval Board for XR16M2750IM Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR16M2750IM48 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
XR16M2750IM48-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16M2751 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO AND POWERSAVE
XR16M2751_07 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*