Lo" />
參數資料
型號： XR16M2750IL-0A-EB
廠商： Exar Corporation
文件頁數： 20/53頁
文件大小： 0K
描述： EVAL BOARD FOR XR16M2750-A 32QFN
標準包裝： 1
系列： *
XR16M2750
27
REV. 1.0.0
1.62V TO 3.63V HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
]
ISR[0]: Interrupt Status
Logic 0 = An interrupt is pending and the ISR contents may be used as a pointer to the appropriate interrupt
service routine.
Logic 1 = No interrupt pending (default condition).
ISR[3:1]: Interrupt Status
These bits indicate the source for a pending interrupt at interrupt priority levels (See Interrupt Source Table 9).
ISR[4]: Xoff/Xon or Special Character Interrupt Status
This bit is set when EFR[4] = 1 and IER[5] = 1. ISR bit-4 indicates that the receiver detected a data match of
the Xoff character(s). If this is an Xoff interrupt, it can be cleared by a read to the ISR. If it is a special character
interrupt, it can be cleared by reading ISR or it will automatically clear after the next character received.
ISR[5]: RTS#/CTS# Interrupt Status
This bit is enabled when EFR[4] = 1. ISR bit-5 indicates that the CTS# or RTS# has been de-asserted.
ISR[7:6]: FIFO Enable Status
These bits are set to a logic 0 when the FIFOs are disabled. They are set to a logic 1 when the FIFOs are
enabled.
4.5
FIFO Control Register (FCR) - Write-Only
This register is used to enable the FIFOs, clear the FIFOs, set the transmit/receive FIFO trigger levels, and
select the DMA mode. The DMA, and FIFO modes are defined as follows:
FCR[0]: TX and RX FIFO Enable
Logic 0 = Disable the transmit and receive FIFO (default).
Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to logic 1 when other FCR bits are
written or they will not be programmed.
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No receive FIFO reset (default)
Logic 1 = Reset the receive FIFO pointers and FIFO level counter logic (the receive shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
TABLE 9: INTERRUPT SOURCE AND PRIORITY LEVEL
PRIORITY
ISR REGISTER STATUS BITS
SOURCE OF INTERRUPT
LEVEL
BIT-5
BIT-4
BIT-3
BIT-2
BIT-1
BIT-0
1
0
1
0
LSR (Receiver Line Status Register)
2
0
1
0
RXRDY (Receive Data Time-out)
3
0
1
0
RXRDY (Received Data Ready)
4
0
1
0
TXRDY (Transmit Ready)
5
0
MSR (Modem Status Register)
6
0
1
0
RXRDY (Received Xoff or Special character)
7
1
0
CTS#, RTS# change of state
-
0
1
None (default)
相關PDF資料
PDF描述
6828318-5 C/A,2.0MM,RISER,XG,AQUA,LC-SC
M3WWK-1020K IDC CABLE - MPL10K/MC10F/MPL10K
UMA1H3R3MDD CAP ALUM 3.3UF 50V 20% RADIAL
M3AKK-1040K IDC CABLE - MSC10K/MC10F/MPK10K
GCM11DREI CONN EDGECARD 22POS .156 EYELET
相關代理商/技術參數
參數描述
XR16M2750IL-0B-EB 功能描述:界面開發工具 Eval Board for XR16M2750IL Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR16M2750IL32 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
XR16M2750IL32-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16M2750IM-0A-EB 功能描述:界面開發工具 Eval Board for XR16M2750IM-0A RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR16M2750IM-0B-EB 功能描述:界面開發工具 Eval Board for XR16M2750IM Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*