- 您現在的位置：買賣IC網 > PDF目錄3761 > XR16L651CM-F (Exar Corporation)IC UART FIFO 32B 48TQFP PDF資料下載
參數資料
| 型號： | XR16L651CM-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 19/56頁 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 32B 48TQFP |
| 標準包裝： | 250 |
| 特點： | * |
| 通道數： | 1，UART |
| FIFO's： | 32 字節 |
| 規程： | 打印機，RS232，RS422，RS485 |
| 電源電壓： | 2.25 V ~ 5.5 V |
| 帶并行端口： | 是 |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-TQFP |
| 供應商設備封裝： | 48-TQFP（7x7） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
XR16L651
á
2.25V TO 5.5V UART WITH 32-BYTE FIFO
REV. 1.3.0
26
4.3.2
IER versus Receive/Transmit FIFO Polled Mode Operation
When FCR bit-0 equals a logic 1 for FIFO enable; resetting IER bits 0-3 enables the XR16L651 in the FIFO
polled mode of operation. Since the receiver and transmitter have separate bits in the LSR either or both can
be used in the polled mode by selecting respective transmit or receive control bit(s).
A. LSR bit-0 indicates there is data in RHR or RX FIFO.
B. LSR bit-1 indicates an overrun error has occurred and that data in the FIFO may not be valid.
C. LSR bits 2-4 provides the type of receive data errors encountered for the data byte in RHR, if any.
D. LSR bit-5 indicates THR is empty.
E. LSR bit-6 indicates when both the transmit FIFO and TSR are empty.
F.
LSR bit-7 indicates a data error in at least one character in the RX FIFO.
IER[0]: RHR Interrupt Enable
The receive data ready interrupt will be issued when RHR has a data character in the non-FIFO mode or when
the receive FIFO has reached the programmed trigger level in the FIFO mode.
Logic 0 = Disable the receive data ready interrupt (default).
Logic 1 = Enable the receiver data ready interrupt.
IER[1]: THR Interrupt Enable
This bit enables the Transmit Ready interrupt which is issued whenever the THR becomes empty in the non-
FIFO mode or when data in the FIFO falls below the programmed trigger level in the FIFO mode. If the THR is
empty when this bit is enabled, an interrupt will be generated.
Logic 0 = Disable Transmit Holding Register empty interrupt (default).
Logic 1 = Enable Transmit Holding Register empty interrupt.
IER[2]: Receive Line Status Interrupt Enable
Any change of state of the LSR register bits 1, 2, 3 or 4 will generate an interrupt to inform the host controller
about the error status of the current data byte in FIFO. LSR bit-1 generates an interrupt immediately when the
character has been received. LSR bits 2-4 generate an interrupt either when the character with errors is next
to be read out of the FIFO (XFR[3] = 0) or when the received chracter is received (XFR[3] = 1).
Logic 0 = Disable the receiver line status interrupt (default).
Logic 1 = Enable the receiver line status interrupt.
IER[3]: Modem Status Interrupt Enable
Logic 0 = Disable the modem status register interrupt (default).
Logic 1 = Enable the modem status register interrupt.
IER[4]: Sleep Mode Enable (requires EFR bit-4 = 1)
Logic 0 = Disable Sleep Mode (default).
Logic 1 = Enable Sleep Mode. See “Sleep Mode & Wake-up Indicator” on page 21.
IER[5]: Xoff Interrupt Enable (requires EFR bit-4=1)
Logic 0 = Disable the software flow control, receive Xoff interrupt (default).
Logic 1 = Enable the software flow control, receive Xoff interrupt. See “Auto Xon/Xoff (Software) Flow
IER[6]: RTS# Output Interrupt Enable (requires EFR bit-4=1)
Logic 0 = Disable the RTS# interrupt (default).
Logic 1 = Enable the RTS# interrupt. The UART issues an interrupt when the RTS# pin makes a transition
from LOW to HIGH.
相關PDF資料 |
PDF描述 |
|---|---|
| XR68C92IJTR-F | DUAL CHANNEL UART 44PLCC |
| XR68C192CVTR-F | IC UART FIFI DUAL 44LQFP |
| ST16C650AIQ48-F | IC UART FIFO 32B 48TQFP |
| XR16L2450IM-F | IC UART FIFO 1B DUAL 48TQFP |
| XR68C192CJTR-F | IC UART FIFI DUAL 44PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16L651CMTR-F | 制造商:Exar Corporation 功能描述:UART 1-CH 32Byte FIFO 2.5V/3.3V/5V 48-Pin TQFP T/R 制造商:Exar Corporation 功能描述:XR16L651CMTR-F |
| XR16L651IM | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| XR16L651IM-F | 功能描述:UART 接口集成電路 UARTW/32BYTEFIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L651IMTR-F | 制造商:Exar Corporation 功能描述:UART 1-CH 32Byte FIFO 2.5V/3.3V/5V 48-Pin TQFP T/R 制造商:Exar Corporation 功能描述:XR16L651IMTR-F |
| XR16L784 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART |
發布緊急采購，3分鐘左右您將得到回復。