參數資料
型號： XCS20XL-5TQ144C
廠商： Xilinx Inc
文件頁數： 83/83頁
文件大小： 0K
描述： IC FPGA 3.3V C-TEMP HP 144TQFP
產品變化通告： Product Discontinuation 26/Oct/2011
標準包裝： 60
系列： Spartan®-XL
LAB/CLB數： 400
邏輯元件/單元數： 950
RAM 位總計： 12800
輸入/輸出數： 113
門數： 20000
電源電壓： 3 V ~ 3.6 V
安裝類型： 表面貼裝
工作溫度： 0°C ~ 85°C
封裝/外殼： 144-LQFP
供應商設備封裝： 144-TQFP（20x20）
Spartan and Spartan-XL FPGA Families Data Sheet
DS060 (v2.0) March 1, 2013
Product Specification
R
Product Obsolete/Under Obsolescence
Output Multiplexer/2-Input Function Generator
(Spartan-XL Family Only)
The output path in the Spartan-XL family IOB contains an
additional multiplexer not available in the Spartan family
IOB. The multiplexer can also be configured as a 2-input
function generator, implementing a pass gate, AND gate,
OR gate, or XOR gate, with 0, 1, or 2 inverted inputs.
When configured as a multiplexer, this feature allows two
output signals to time-share the same output pad, effec-
tively doubling the number of device outputs without requir-
ing a larger, more expensive package. The select input is
the pin used for the output flip-flop clock, OK.
When the multiplexer is configured as a 2-input function
generator, logic can be implemented within the IOB itself.
Combined with a Global buffer, this arrangement allows
very high-speed gating of a single signal. For example, a
wide decoder can be implemented in CLBs, and its output
gated with a Read or Write Strobe driven by a global buffer.
The user can specify that the IOB function generator be
used by placing special library symbols beginning with the
letter "O." For example, a 2-input AND gate in the IOB func-
tion generator is called OAND2. Use the symbol input pin
labeled "F" for the signal on the critical path. This signal is
placed on the OK pin — the IOB input with the shortest
delay to the function generator. Two examples are shown in
Output Buffer
An active High 3-state signal can be used to place the out-
put buffer in a high-impedance state, implementing 3-state
outputs or bidirectional I/O. Under configuration control, the
output (O) and output 3-state (T) signals can be inverted.
The polarity of these signals is independently configured for
each IOB (see Figure 6, page 7). An output can be config-
ured as open-drain (open-collector) by tying the 3-state pin
(T) to the output signal, and the input pin (I) to Ground.
By default, a 5V Spartan device output buffer pull-up struc-
ture is configured as a TTL-like totem-pole. The High driver
is an n-channel pull-up transistor, pulling to a voltage one
transistor threshold below VCC. Alternatively, the outputs
can be globally configured as CMOS drivers, with additional
p-channel pull-up transistors pulling to VCC. This option,
applied using the bitstream generation software, applies to
all outputs on the device. It is not individually programma-
ble.
All Spartan-XL device outputs are configured as CMOS
drivers, therefore driving rail-to-rail. The Spartan-XL family
outputs are individually programmable for 12 mA or 24 mA
output drive.
Any 5V Spartan device with its outputs configured in TTL
mode can drive the inputs of any typical 3.3V device. Sup-
ported destinations for Spartan/XL device outputs are
shown in Table 7.
Three-State Register (Spartan-XL Family Only)
Spartan-XL devices incorporate an optional register control-
ling the three-state enable in the IOBs. The use of the
three-state control register can significantly improve output
enable and disable time.
Output Slew Rate
The slew rate of each output buffer is, by default, reduced,
to minimize power bus transients when switching non-criti-
cal signals. For critical signals, attach a FAST attribute or
property to the output buffer or flip-flop.
Spartan/XL devices have a feature called "Soft Start-up,"
designed to reduce ground bounce when all outputs are
turned on simultaneously at the end of configuration.
When the configuration process is finished and the device
starts up, the first activation of the outputs is automatically
slew-rate limited. Immediately following the initial activation
of the I/O, the slew rate of the individual outputs is deter-
mined by the individual configuration option for each IOB.
Pull-up and Pull-down Network
Programmable pull-up and pull-down resistors are used for
tying unused pins to VCC or Ground to minimize power con-
sumption and reduce noise sensitivity. The configurable
pull-up resistor is a p-channel transistor that pulls to VCC.
The configurable pull-down resistor is an n-channel transis-
tor that pulls to Ground. The value of these resistors is typi-
cally
20 K
Figure 7: AND and MUX Symbols in Spartan-XL IOB
DS060_07_081100
OAND2
OMUX2
F
D0
D1
O
S0
相關PDF資料
PDF描述
65801-053LF CLINCHER RECEPTACLE ASSY GOLD
IDT70V3379S4BCG IC SRAM 576KBIT 4NS 256BGA
KMPC8555PXAQF IC MPU POWERQUICC III 783-FCPBGA
KMPC8555PXAPF IC MPU POWERQUICC III 783-FCPBGA
IDT70V3379S4BC IC SRAM 576KBIT 4NS 256BGA
相關代理商/技術參數
參數描述
XCS20XL-5TQ144I 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan and Spartan-XL Families Field Programmable Gate Arrays
XCS20XL-5TQ208C 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan and Spartan-XL Families Field Programmable Gate Arrays
XCS20XL-5TQ208I 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan and Spartan-XL Families Field Programmable Gate Arrays
XCS20XL-5TQ240C 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan and Spartan-XL Families Field Programmable Gate Arrays
XCS20XL-5TQ240I 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan and Spartan-XL Families Field Programmable Gate Arrays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*