- 您現在的位置：買賣IC網 > PDF目錄4149 > XC4028XL-3HQ240I (Xilinx Inc)IC FPGA I-TEMP 3.3V 3SPD 240HQFP PDF資料下載
參數資料
| 型號： | XC4028XL-3HQ240I |
| 廠商： | Xilinx Inc |
| 文件頁數： | 38/68頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC FPGA I-TEMP 3.3V 3SPD 240HQFP |
| 產品變化通告： | Product Discontinuation 27/Apr/2010 |
| 標準包裝： | 1 |
| 系列： | XC4000E/X |
| LAB/CLB數： | 1024 |
| 邏輯元件/單元數： | 2432 |
| RAM 位總計： | 32768 |
| 輸入/輸出數： | 193 |
| 門數： | 28000 |
| 電源電壓： | 3 V ~ 3.6 V |
| 安裝類型： | 表面貼裝 |
| 工作溫度： | -40°C ~ 100°C |
| 封裝/外殼： | 240-BFQFP 裸露焊盤 |
| 供應商設備封裝： | 240-PQFP（32x32） |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
R
May 14, 1999 (Version 1.6)
6-47
XC4000E and XC4000X Series Field Programmable Gate Arrays
6
is passed through and is captured by each FPGA when it
recognizes the 0010 preamble. Following the length-count
data, each FPGA outputs a High on DOUT until it has
received its required number of data frames.
After an FPGA has received its conguration data, it
passes on any additional frame start bits and conguration
data on DOUT. When the total number of conguration
clocks applied after memory initialization equals the value
of the 24-bit length count, the FPGAs begin the start-up
sequence and become operational together. FPGA I/O are
normally released two CCLK cycles after the last congura-
tion bit is received. Figure 47 on page 53 shows the
start-up timing for an XC4000 Series device.
The daisy-chained bitstream is not simply a concatenation
of the individual bitstreams. The PROM le formatter must
be used to combine the bitstreams for a daisy-chained con-
guration.
Multi-Family Daisy Chain
All Xilinx FPGAs of the XC2000, XC3000, and XC4000
Series use a compatible bitstream format and can, there-
fore, be connected in a daisy chain in an arbitrary
sequence. There is, however, one limitation. The lead
device must belong to the highest family in the chain. If the
chain contains XC4000 Series devices, the master nor-
mally cannot be an XC2000 or XC3000 device.
The reason for this rule is shown in Figure 47 on page 53.
Since all devices in the chain store the same length count
value and generate or receive one common sequence of
CCLK pulses, they all recognize length-count match on the
same CCLK edge, as indicated on the left edge of
Figure 47. The master device then generates additional
CCLK pulses until it reaches its nish point F. The different
families generate or require different numbers of additional
CCLK pulses until they reach F. Not reaching F means that
the device does not really nish its conguration, although
DONE may have gone High, the outputs became active,
and the internal reset was released. For the XC4000 Series
device, not reaching F means that readback cannot be ini-
tiated and most boundary scan instructions cannot be
used.
The user has some control over the relative timing of these
events and can, therefore, make sure that they occur at the
proper time and the nish point F is reached. Timing is con-
trolled using options in the bitstream generation software.
XC3000 Master with an XC4000 Series Slave
Some designers want to use an inexpensive lead device in
peripheral mode and have the more precious I/O pins of the
XC4000 Series devices all available for user I/O. Figure 44
provides a solution for that case.
This solution requires one CLB, one IOB and pin, and an
internal oscillator with a frequency of up to 5 MHz as a
clock source. The XC3000 master device must be cong-
ured with late Internal Reset, which is the default option.
One CLB and one IOB in the lead XC3000-family device
are used to generate the additional CCLK pulse required by
the XC4000 Series devices. When the lead device removes
the internal RESET signal, the 2-bit shift register responds
to its clock input and generates an active Low output signal
for the duration of the subsequent clock period. An external
connection between this output and CCLK thus creates the
extra CCLK pulse.
Output
Connected
to CCLK
OE/T
0
1
0
.
0
1
.
Reset
X5223
etc
Active Low Output
Active High Output
Figure 44: CCLK Generation for XC3000 Master
Driving an XC4000 Series Slave
Product Obsolete or Under Obsolescence
相關PDF資料 |
PDF描述 |
|---|---|
| XC4028XL-3HQ240C | IC FPGA C-TEMP 3.3V 3SPD 240HQFP |
| XC4028XL-3HQ208I | IC FPGA I-TEMP 3.3V 3SPD 208HQFP |
| XC4028XL-3HQ208C | IC FPGA C-TEMP 3.3V 3SPD 208HQFP |
| XC4028XL-3HQ160I | IC FPGA I-TEMP 3.3V 3SPD 160HQFP |
| XC4028XL-3HQ160C | IC FPGA C-TEMP 3.3V 3SPD 160HQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XC4028XL-3HQ304C | 功能描述:IC FPGA C-TEMP 3.3V 3SPD 304HQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:XC4000E/X 標準包裝:1 系列:Kintex-7 LAB/CLB數:25475 邏輯元件/單元數:326080 RAM 位總計:16404480 輸入/輸出數:350 門數:- 電源電壓:0.97 V ~ 1.03 V 安裝類型:表面貼裝 工作溫度:0°C ~ 85°C 封裝/外殼:900-BBGA，F(xiàn)CBGA 供應商設備封裝:900-FCBGA（31x31） 其它名稱:122-1789 |
| XC4028XL-3HQ304I | 功能描述:IC FPGA I-TEMP 3.3V 3SPD 304HQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:XC4000E/X 標準包裝:1 系列:Kintex-7 LAB/CLB數:25475 邏輯元件/單元數:326080 RAM 位總計:16404480 輸入/輸出數:350 門數:- 電源電壓:0.97 V ~ 1.03 V 安裝類型:表面貼裝 工作溫度:0°C ~ 85°C 封裝/外殼:900-BBGA，F(xiàn)CBGA 供應商設備封裝:900-FCBGA（31x31） 其它名稱:122-1789 |
| XC4028XL-3PG299C | 制造商:Xilinx 功能描述: |
| XC4028XLA-07HQ240C | 制造商:Xilinx 功能描述: |
| XC4028XLA-08BG352C0314 | 制造商:Xilinx 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。