- 您現在的位置：買賣IC網 > PDF目錄4159 > XC4013E-1HQ208C (Xilinx Inc)IC FPGA C-TEMP 5V 1SPD 208-HQFP PDF資料下載
參數資料
| 型號： | XC4013E-1HQ208C |
| 廠商： | Xilinx Inc |
| 文件頁數： | 59/68頁 |
| 文件大小： | 0K |
| 描述： | IC FPGA C-TEMP 5V 1SPD 208-HQFP |
| 產品變化通告： | XC1700 PROMs,XC5200,HQ,SCD Parts Discontinuation 19/Jul/2010 |
| 標準包裝： | 1 |
| 系列： | XC4000E/X |
| LAB/CLB數： | 576 |
| 邏輯元件/單元數： | 1368 |
| RAM 位總計： | 18432 |
| 輸入/輸出數： | 160 |
| 門數： | 13000 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 工作溫度： | 0°C ~ 85°C |
| 封裝/外殼： | 208-BFQFP 裸露焊盤 |
| 供應商設備封裝： | 208-PQFP（28x28） |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁當前第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
R
XC4000E and XC4000X Series Field Programmable Gate Arrays
6-66
May 14, 1999 (Version 1.6)
Asynchronous Peripheral Mode
Write to FPGA
Asynchronous Peripheral mode uses the trailing edge of
the logic AND condition of WS and CS0 being Low and RS
and CS1 being High to accept byte-wide data from a micro-
processor bus. In the lead FPGA, this data is loaded into a
double-buffered UART-like parallel-to-serial converter and
is serially shifted into the internal logic.
The lead FPGA presents the preamble data (and all data
that overows the lead device) on its DOUT pin. The
RDY/BUSY output from the lead FPGA acts as a hand-
shake signal to the microprocessor. RDY/BUSY goes Low
when a byte has been received, and goes High again when
the byte-wide input buffer has transferred its information
into the shift register, and the buffer is ready to receive new
data. A new write may be started immediately, as soon as
the RDY/BUSY output has gone Low, acknowledging
receipt of the previous data. Write may not be terminated
until RDY/BUSY is High again for one CCLK period. Note
that RDY/BUSY is pulled High with a high-impedance
pull-up prior to INIT going High.
The length of the BUSY signal depends on the activity in
the UART. If the shift register was empty when the new byte
was received, the BUSY signal lasts for only two CCLK
periods. If the shift register was still full when the new byte
was received, the BUSY signal can be as long as nine
CCLK periods.
Note that after the last byte has been entered, only seven of
its bits are shifted out. CCLK remains High with DOUT
equal to bit 6 (the next-to-last bit) of the last byte entered.
The READY/BUSY handshake can be ignored if the delay
from any one Write to the end of the next Write is guaran-
teed to be longer than 10 CCLK periods.
Status Read
The logic AND condition of the CS0, CS1and RS inputs
puts the device status on the Data bus.
D7 High indicates Ready
D7 Low indicates Busy
D0 through D6 go unconditionally High
It is mandatory that the whole start-up sequence be started
and completed by one byte-wide input. Otherwise, the pins
used as Write Strobe or Chip Enable might become active
outputs and interfere with the nal byte transfer. If this
transfer does not occur, the start-up sequence is not com-
pleted all the way to the nish (point F in Figure 47 on page
In this case, at worst, the internal reset is not released. At
best, Readback and Boundary Scan are inhibited. The
length-count value, as generated by the XACT
step soft-
ware, ensures that these problems never occur.
Although RDY/BUSY is brought out as a separate signal,
microprocessors can more easily read this information on
one of the data lines. For this purpose, D7 represents the
RDY/BUSY status when RS is Low, WS is High, and the
two chip select lines are both active.
Asynchronous Peripheral mode is selected by a <101> on
the mode pins (M2, M1, M0).
ADDRESS
BUS
DATA
BUS
ADDRESS
DECODE
LOGIC
CS0
...
RDY/BUSY
WS
PROGRAM
D0–7
CCLK
DOUT
DIN
M2
M0
M1
N/C
RS
CS1
CONTROL
SIGNALS
INIT
REPROGRAM
OPTIONAL
DAISY-CHAINED
FPGAs
VCC
DONE
8
X9028
4.7 k
4.7 k
4.7 k
4.7 k
XC4000E/X
ASYNCHRO-
NOUS
PERIPHERAL
PROGRAM
CCLK
DOUT
M2
M0
M1
INIT
DONE
XC4000E/X
SLAVE
Figure 58:
Asynchronous Peripheral Mode Circuit Diagram
Product Obsolete or Under Obsolescence
相關PDF資料 |
PDF描述 |
|---|---|
| XC4013E-1BG225C | IC FPGA C-TEMP 5V 1SPD 225-PBGA |
| AMC44DRTN-S734 | CONN EDGECARD 88POS DIP .100 SLD |
| 65801-009LF | CONN RCPT 9POS 2.54MM VERT TIN |
| AMC44DRTH-S734 | CONN EDGECARD 88POS DIP .100 SLD |
| AMC44DREN-S734 | CONN EDGECARD 88POS .100 EYELET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XC4013E-1HQ208I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA) |
| XC4013E-1HQ240C | 功能描述:IC FPGA C-TEMP 5V 1SPD 240-HQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:XC4000E/X 標準包裝:1 系列:Kintex-7 LAB/CLB數:25475 邏輯元件/單元數:326080 RAM 位總計:16404480 輸入/輸出數:350 門數:- 電源電壓:0.97 V ~ 1.03 V 安裝類型:表面貼裝 工作溫度:0°C ~ 85°C 封裝/外殼:900-BBGA，F(xiàn)CBGA 供應商設備封裝:900-FCBGA（31x31） 其它名稱:122-1789 |
| XC4013E-1HQ240I | 制造商:XILINX 制造商全稱:XILINX 功能描述:XC4000E and XC4000X Series Field Programmable Gate Arrays |
| XC4013E-1HQ240M | 制造商:XILINX 制造商全稱:XILINX 功能描述:XC4000E and XC4000X Series Field Programmable Gate Arrays |
| XC4013E-1MQ240C | 制造商:XILINX 制造商全稱:XILINX 功能描述:XC4000E and XC4000X Series Field Programmable Gate Arrays |
發布緊急采購，3分鐘左右您將得到回復。