- 您現在的位置：買賣IC網 > PDF目錄4176 > XC3164A-3PC84C (Xilinx Inc)IC LOGIC CL ARRAY 6400GAT 84PLCC PDF資料下載
參數資料
| 型號： | XC3164A-3PC84C |
| 廠商： | Xilinx Inc |
| 文件頁數： | 31/76頁 |
| 文件大小： | 0K |
| 描述： | IC LOGIC CL ARRAY 6400GAT 84PLCC |
| 產品變化通告： | XC4000XL/E, XC9500XV, XC3100A Discontinuance 12/Apr/2010 |
| 標準包裝： | 15 |
| 系列： | XC3000A/L |
| LAB/CLB數： | 224 |
| RAM 位總計： | 46064 |
| 輸入/輸出數： | 70 |
| 門數： | 4500 |
| 電源電壓： | 4.25 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 工作溫度： | 0°C ~ 85°C |
| 封裝/外殼： | 84-LCC（J 形引線） |
| 供應商設備封裝： | 84-PLCC |
| 其它名稱： | 122-1045 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
R
November 9, 1998 (Version 3.1)
7-39
XC3000 Series Field Programmable Gate Arrays
7
AND of several slave mode devices, a hold-off signal for a
master mode device. After configuration this pin becomes a
user-programmable I/O pin.
BCLKIN
This is a direct CMOS level input to the alternate clock
buffer (Auxiliary Buffer) in the lower right corner.
XTL1
This user I/O pin can be used to operate as the output of an
amplifier driving an external crystal and bias circuitry.
XTL2
This user I/O pin can be used as the input of an amplifier
connected to an external crystal and bias circuitry. The I/O
Block is left unconfigured. The oscillator configuration is
activated by routing a net from the oscillator buffer symbol
output and by the MakeBits program.
CS0, CS1, CS2, WS
These four inputs represent a set of signals, three active
Low and one active High, that are used to control configu-
ration-data entry in the Peripheral mode. Simultaneous
assertion of all four inputs generates a Write to the internal
data buffer. The removal of any assertion clocks in the
D0-D7 data. In Master-Parallel mode, WS and CS2 are the
A0 and A1 outputs. After configuration, these pins are
user-programmable I/O pins.
RDY/BUSY
During Peripheral Parallel mode configuration this pin indi-
cates when the chip is ready for another byte of data to be
written to it. After configuration is complete, this pin
becomes a user-programmed I/O pin.
RCLK
During Master Parallel mode configuration, each change
on the A0-15 outputs is preceded by a rising edge on
RCLK, a redundant output signal. After configuration is
complete, this pin becomes a user-programmed I/O pin.
D0-D7
This set of eight pins represents the parallel configuration
byte for the parallel Master and Peripheral modes. After
configuration is complete, they are user-programmed I/O
pins.
A0-A15
During Master Parallel mode, these 16 pins present an
address output for a configuration EPROM. After configura-
tion, they are user-programmable I/O pins.
DIN
During Slave or Master Serial configuration, this pin is used
as a serial-data input. In the Master or Peripheral configu-
ration, this is the Data 0 input. After configuration is com-
plete, this pin becomes a user-programmed I/O pin.
DOUT
During configuration this pin is used to output serial-config-
uration data to the DIN pin of a daisy-chained slave. After
configuration is complete, this pin becomes a user-pro-
grammed I/O pin.
TCLKIN
This is a direct CMOS-level input to the global clock buffer.
This pin can also be configured as a user programmable
I/O pin. However, since TCLKIN is the preferred input to the
global clock net, and the global clock net should be used as
the primary clock source, this pin is usually the clock input
to the chip.
Unrestricted User I/O Pins
I/O
An I/O pin may be programmed by the user to be an Input
or an Output pin following configuration. All unrestricted I/O
pins, plus the special pins mentioned on the following page,
have a weak pull-up resistor that becomes active as soon
as the device powers up, and stays active until the end of
configuration.
Note:
Before and during configuration, all outputs that are not used for the configuration process are 3-stated with a weak
pull-up resistor.
Product Obsolete or Under Obsolescence
相關PDF資料 |
PDF描述 |
|---|---|
| AMC36DRYN-S13 | CONN EDGECARD 72POS .100 EXTEND |
| XC3142A-3PQ100C | IC LOGIC CL ARRAY 4200GAT 100PQF |
| AMC36DRYH-S13 | CONN EDGECARD 72POS .100 EXTEND |
| XC3130A-3PQ100C | IC LOGIC CL ARRAY 3000GAT 100PQF |
| XC3130A-3PC84C | IC LOGIC CL ARRAY 3000GAT 84PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XC3164A-3PC84I | 制造商:Xilinx 功能描述: |
| XC3164A-3PQ160C | 制造商:Xilinx 功能描述: |
| XC3164A-3PQ160I | 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays (XC3000A/L, XC3100A/L) |
| XC3164A-3TQ144C | 功能描述:IC FPGA 224 CLB'S 144-TQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:XC3000A/L 產品變化通告:XC4000(E,L) Discontinuation 01/April/2002 標準包裝:24 系列:XC4000E/X LAB/CLB數:100 邏輯元件/單元數:238 RAM 位總計:3200 輸入/輸出數:80 門數:3000 電源電壓:4.5 V ~ 5.5 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 100°C 封裝/外殼:120-BCBGA 供應商設備封裝:120-CPGA（34.55x34.55） |
| XC3164A-3TQ144I | 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays (XC3000A/L, XC3100A/L) |
發布緊急采購，3分鐘左右您將得到回復。