- 您現在的位置：買賣IC網 > PDF目錄4176 > XC3042A-7PQ100C (Xilinx Inc)IC LOGIC CL ARRAY 4200GAT 100PQF PDF資料下載
參數資料
| 型號： | XC3042A-7PQ100C |
| 廠商： | Xilinx Inc |
| 文件頁數： | 29/76頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LOGIC CL ARRAY 4200GAT 100PQF |
| 產品變化通告： | Product Discontinuation 27/Apr/2010 |
| 標準包裝： | 1 |
| 系列： | XC3000A/L |
| LAB/CLB數： | 144 |
| RAM 位總計： | 30784 |
| 輸入/輸出數： | 82 |
| 門數： | 3000 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 工作溫度： | 0°C ~ 85°C |
| 封裝/外殼： | 100-BQFP |
| 供應商設備封裝： | 100-QFP（14x20） |
| 其它名稱： | 122-1026 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
R
November 9, 1998 (Version 3.1)
7-37
XC3000 Series Field Programmable Gate Arrays
7
Dynamic Power Consumption
Power Consumption
The Field Programmable Gate Array exhibits the low power
consumption characteristic of CMOS ICs. For any design,
the configuration option of TTL chip input threshold
requires power for the threshold reference. The power
required by the static memory cells that hold the configura-
tion data is very low and may be maintained in a
power-down mode.
Typically, most of power dissipation is produced by external
capacitive loads on the output buffers. This load and fre-
quency dependent power is 25
W/pF/MHz per output.
Another component of I/O power is the external dc loading
on all output pins.
Internal power dissipation is a function of the number and
size of the nodes, and the frequency at which they change.
In an FPGA, the fraction of nodes changing on a given
clock is typically low (10-20%). For example, in a long
binary counter, the total activity of all counter flip-flops is
equivalent to that of only two CLB outputs toggling at the
clock frequency. Typical global clock-buffer power is
between 2.0 mW/MHz for the XC3020A and 3.5 mW/MHz
for the XC3090A. The internal capacitive load is more a
function of interconnect than fan-out. With a typical load of
three general interconnect segments, each CLB output
requires about 0.25 mW per MHz of its output frequency.
Because the control storage of the FPGA is CMOS static
memory, its cells require a very low standby current for data
retention. In some systems, this low data retention current
characteristic can be used as a method of preserving con-
figurations in the event of a primary power loss. The FPGA
has built in powerdown logic which, when activated, will
disable normal operation of the device and retain only the
configuration data. All internal operation is suspended and
output buffers are placed in their high-impedance state with
no pull-ups. Different from the XC3000 family which can be
powered down to a current consumption of a few micro-
amps, the XC3100A draws 5 mA, even in power-down.
This makes power-down operation less meaningful. In con-
trast, ICCPD for the XC3000L is only 10 A.
To force the FPGA into the Powerdown state, the user must
pull the PWRDWN pin Low and continue to supply a reten-
tion voltage to the VCC pins. When normal power is
restored, VCC is elevated to its normal operating voltage
and PWRDWN is returned to a High. The FPGA resumes
operation with the same internal sequence that occurs at
the conclusion of configuration. Internal-I/O and logic-block
storage elements will be reset, the outputs will become
enabled and the DONE/PROG pin will be released.
When VCC is shut down or disconnected, some power
might unintentionally be supplied from an incoming signal
driving an I/O pin. The conventional electrostatic input pro-
tection is implemented with diodes to the supply and
ground. A positive voltage applied to an input (or output)
will cause the positive protection diode to conduct and drive
the VCC connection. This condition can produce invalid
power conditions and should be avoided. A large series
resistor might be used to limit the current or a bipolar buffer
may be used to isolate the input signal.
XC3042A
XC3042L
XC3142A
One CLB driving three local interconnects
0.25
0.17
0.25
mW per MHz
One global clock buffer and clock line
2.25
1.40
1.70
mW per MHz
One device output with a 50 pF load
1.25
mW per MHz
Product Obsolete or Under Obsolescence
相關PDF資料 |
PDF描述 |
|---|---|
| ABC65DRES-S734 | CONN EDGECARD 130PS .100 EYELET |
| A14V40A-PQG160C | IC FPGA 4K GATES 3.3V 160-PQFP |
| EMC18DTEF | CONN EDGECARD 36POS .100 EYELET |
| A1425A-1PQ160I | IC FPGA 2500 GATES 160-PQFP |
| A1440A-PQG160I | IC FPGA 4K GATES 160-PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XC3042A-7PQ100C0167 | 制造商:Xilinx 功能描述: |
| XC3042A-7PQ100C0262 | 制造商:Xilinx 功能描述: |
| XC3042A-7PQ100C0341 | 制造商:Xilinx 功能描述: |
| XC3042A-7PQ100I | 制造商: 功能描述: 制造商:undefined 功能描述: |
| XC3042A-7PQG100I | 制造商:Xilinx 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。